Results 31 to 40 of about 2,551 (259)
Laser Marked and Textured Biomaterial Evaluated by Mott-Schottky Technique
International Journal of Electrochemical Science, 2017 The effect of an optical fiber laser marking and texturing techniques on the surface of the ISO 5832-1 stainless steel via the Mott-Schottky approach was evaluated in this work.
Eurico Felix Pieretti +1 more
doaj +1 more source
Influence of laser texturing on tribological properties of DLC coatings
Production Engineering Archives, 2021 The work presents the use of laser texturing of DLC coatings to improve tribological properties. The coatings were applied by the PVD method to the rings made of 4H13 steel.
Radek Norbert +3 more
doaj +1 more source
Modification of aluminum alloy surface properties by wave-long laser texturing
MATEC Web of Conferences, 2017 Change of the static contact angle (SCA) of 10 μL distilled water droplet on laser textured aluminium alloy (AMG-6) substrates was studied. The texture was deposited by a laser system based on a fiber laser. An increase in the power of laser radiation is
Batishcheva Kseniya +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Development of antibacterial steel surfaces through laser texturing
APL Materials, 2020 The aim of the present study was to develop novel antibacterial touch surfaces through the laser texturing optimization of stainless steel. A wide range of laser fluence (2.11 J/cm2–5.64 J/cm2) and scanning interval (10 µm–30 μm) parameters were explored.
Victor M. Villapún +8 more
doaj +1 more source
Friction, 2022 Shallow Hilbert curve patterns with easily programmable texture density were selected for laser texturing of stainless steel substrates. Two different texture path segment lengths (12 and 24 µm) and four different laser power percentages (5%, 10%, 15 ...
Firuze Soltani-Kordshuli +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Laser surface texturing of tool steel: textured surfaces quality evaluation
Open Engineering, 2016 In this experimental investigation the laser surface texturing of tool steel of type 90MnCrV8 has been conducted. The 5-axis highly dynamic laser precision machining centre Lasertec 80 Shape equipped with the nano-second pulsed ytterbium fibre laser and ...
Šugár Peter +2 more
doaj +1 more source
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source