Results 101 to 110 of about 24,156 (348)
Characterizing anomalies in distributed strain measurements of cast-in-situ bored piles [PDF]
, 2016 This paper describes the method of identifying typical defects of bored cast-in-situ piles when instrumenting using Distributed Optical Fiber Strain Sensing (DOFSS).
Ang, K. A. +3 more
core +2 more sources
Triplet‐Triplet Annihilation Enhances Photochemical Curing Contrast for Vat‐Based 3D Printing
Advanced Functional Materials, EarlyView.Triplet–triplet annihilation photopolymerization (TTAP) resins enhance curing contrast for digital light processing (DLP) 3D printing compared to conventional Type I and II photopolymerizations at matched optical densities. By exploiting a superlinear initiation response, TTAP preserves fine details, allowing reliable fabrication of complex structures ...
Connor J. O'Dea +2 more
wiley +1 more source
Pile Performance Assessment under Induced Lateral Loading [PDF]
, 2016 This research work focuses on determining the internal force distribution in piles from displacement measurements when the piles no longer behave fully elastically.
Fuentes, R, Rontogianni, S
core
Image based simulation of one-dimensional compression tests on carbonate sand [PDF]
, 2019 High factors of safety and conservative methods are commonly used on foundation design on shelly carbonate soils. A better understanding of the behavior of this material is, thus, critical for more sustainable approaches for the design of a number of ...
A Munjiza +12 more
core +2 more sources
Advanced Functional Materials, EarlyView.ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo +10 more
wiley +1 more source
Installation Behavior of Open Ended and Closed Ended Piles with Torque Application [PDF]
, 2018 Screw piles offer several potential benefits for deployment offshore for renewable energy developments. They are easy to install, have the potential to achieve large capacity and generate low noise and vibration during installation.
Brown, Michael +2 more
core +2 more sources
Dispensing Volumetric Additive Manufacturing
Advanced Functional Materials, EarlyView.Dispensing volumetric additive manufacturing (DVAM) prints 3D structures inside a photocurable resin droplet suspended from the tip of a glass pipette, enabling sequential printing without resin vats or manual part removal. Real‐time droplet profiling and ray‐tracing‐based correction compensate for optical distortion at the curved resin‐air interface ...
Hongryung Jeon +5 more
wiley +1 more source
“Analysis of The Lateral Response of A Reinforced Concrete Pile Penetrated In Sand Soil Using Finite Element” [PDF]
Pile foundations are slender elements, underneath a major structure, frequently used for many decades as load carrying and load transferring systems from shallow inadequate subsurface soil layers to deep and stiff bearing strata with high degree of ...
Alkhaddar, R +3 more
core
Remoulding of the Mercia Mudstone Group around CFA pile shafts [PDF]
, 2013 A field test has been undertaken to investigate changes to in situ Mercia Mudstone at the pile soil interface after installation of four 5.5 m long 350 mm diameter CFA piles. The test investigated whether a remoulded zone exists, the extent of the zone,
Atkinson +3 more
core +1 more source
Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films
Advanced Functional Materials, EarlyView.Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee +5 more
wiley +1 more source