Journal of the Korean Wood Science and Technology, 2016 Relatively little information is available regarding the correlation between wood and veneer quality, especially for Samama wood, an endemic wood species in eastern Indonesia. This study addresses the quality of 8 years old Samama wood and its effect on the veneer quality.
Tekat Dwi Cahyono +5 more
openaire +4 more sources
Comparison of the Dynamic Cut-Out Failure Modes of Common Proximal Femoral Fixation Devices Using a Mesh-Free Computational Method. [PDF]
J Orthop ResMigration and cut‐out of DHS, Gamma3, PFNA‐II, and TFNA were compared under dynamic loading in a stable intertrochanteric fracture benchtop foam model and a mesh‐free simulation. No significant differences in force at cut‐out were observed, but simulation revealed that the volumes of damaged bone foam were 15%, 32%, and 25% higher for the Gamma3, PFNA,
Boles EU +6 more
europepmc +2 more sources
Turn-by-wire: Computationally mediated physical fabrication [PDF]
, 2019 Advances in digital fabrication have simultaneously created new capabilities while reinforcing outdated workflows that constrain how, and by whom, these fabrication tools are used.
Gupta Sidhant +6 more
core +1 more source
Short-term manpower management in manufacturing systems: new requirements and DSS prototyping [PDF]
, 2000 The short-term planning and scheduling of discrete manufacturing systems has mostly focused in the past on the management of machines, implicitly considered as the critical resources of the workshops.
Grabot, Bernard, Letouzey, Agnès
core +2 more sources
Distributed machining control and monitoring using smart sensors/actuators [PDF]
, 2004 The study of smart sensors and actuators led, during the past few years, to the development of facilities which improve traditional sensors and actuators in a necessary way to automate production systems. In an other context, many studies are carried out
Desforges, Xavier +3 more
core +3 more sources
Projekt for manufacturing of gears for Company Stab spol. s r. o. [PDF]
, 2020 Diplomová práca opisuje projekt na založenie novej divízie pre firmu ktorá sa zaoberá generálnymi opravami strojov. V prvej časti práce je rozoberaná teoretická časť o výrobnom procese ozubenia a ekonomická časť tejto práce. Hlávne časti práce sú analýza
Štefan Staník
core
Numerical study of the influence of veneer lathe checks on the elastic mechanical properties of laminated veneer lumber (LVL) made of beech [PDF]
Holzforschung, 2014 Abstract Laminated veneer lumber (LVL) is a well-known high-performance engineered wood product suitable for structural applications. However, the peeling process can induce lathe checks of the veneer with various depth and spatial frequencies.
DENAUD, Louis +2 more
openaire +2 more sources
Lathe check development and properties: effect of log soaking temperature, compression rate, cutting radius and cutting speed during peeling process of European beech (Fagus sylvatica L.) veneer [PDF]
European Journal of Wood and Wood Products, 2018 The depth of lathe checks and integrity of veneer have been shown to be critical factors affecting the bonding process but also affecting the mechanical properties of veneer-based products. This study shows how beech (Fagus sylvatica L.) veneer lathe checks interval and depths are affected by soaking temperature, compression rate, cutting radius and ...
Rohumaa, Anti +4 more
openaire +3 more sources
Design of an instrumented smart cutting tool and its implementation and application perspectives [PDF]
, 2014 This paper presents an innovative design of a smart cutting tool, using two surface acoustic wave (SAW) strain sensors mounted onto the top and the side surface of the tool shank respectively, and its implementation and application perspectives.
Chen, X +4 more
core +1 more source
Analytical modeling of chatter stability in turning and boring operations - Part II: Experimental verification [PDF]
, 2007 In this part of the paper series, chatter experiments are conducted in order to verify the proposed stability models presented in the first part (Ozlu, E., and Budak, E., 2007, ASME J. Manuf. Sci. Eng., 129(4), pp. 726–732).
Budak, Erhan, Özlü, Emre
core +1 more source