Results 31 to 40 of about 169 (118)

Automation of lathe checks detection using deep learning

Abstract Automated detection of lathe checks in wood veneers presents significant challenges due to the variability of lathe checks characteristics and the natural properties of wood. This study explores the use of two convolutional neural networks (U-Net architecture) to enhance the precision and efficiency of lathe checks detection in poplar ...
Caroline Marc, Bertrand Marcon, Louis Denaud, Stéphane Girardon   +3 more
openaire   +1 more source

Experimental Evaluation of Turning AISI 304 Using Minimum Quantity Lubrication With Vegetable‐Based Green Cutting Fluids

MetalMat, Volume 3, Issue 1, March 2026.
This study experimentally evaluates the performance of eco‐friendly vegetable‐based cutting fluids—coconut, sunflower, and palm oils—during turning of AISI 304 stainless steel under minimum quantity lubrication. Palm oil exhibited superior lubrication and cooling characteristics, yielding the lowest cutting force, temperature, and surface roughness ...
Ranjith Ravindran Nair, Praveen Vijayan, Jayesh Shanthi Bhavan, Ajin C. Sajeevan   +3 more
wiley   +1 more source

Comparison of the Dynamic Cut‐Out Failure Modes of Common Proximal Femoral Fixation Devices Using a Mesh‐Free Computational Method

Journal of Orthopaedic Research, Volume 44, Issue 2, February 2026.
Migration and cut‐out of DHS, Gamma3, PFNA‐II, and TFNA were compared under dynamic loading in a stable intertrochanteric fracture benchtop foam model and a mesh‐free simulation. No significant differences in force at cut‐out were observed, but simulation revealed that the volumes of damaged bone foam were 15%, 32%, and 25% higher for the Gamma3, PFNA,
Erica Ueda Boles, Sloan Kulper, Katie Whiffin, Marilyn Janice Oentaryo, Kerstin Schneider, Frankie Leung, Christian X. Fang   +6 more
wiley   +1 more source

Efecto de un envejecimiento acelerado mediante rayos UV en la propagación superficial de grietas de debobinado en tableros contrachapados de Eucalyptus nitens

Maderas: Ciencia y Tecnología, 2014
El objetivo de este estudio fue evaluar el efecto de un envejecimiento acelerado mediante rayos ultravioleta y condiciones ambientales controladas sobre la propagación de grietas de debobinado y agrietamiento superficial, al simular las condiciones de ...
Andrés Acevedo, Cecilia Bustos, Jean Pierre Lasserre, William Gacitúa   +3 more
doaj  

A Maintenance 4.0 Framework for Proactive Indoor Air Quality Management in Laboratory Environments

Indoor Air, Volume 2026, Issue 1, 2026.
This study presents an advanced Maintenance 4.0 framework designed for the systematic assessment and mitigation of indoor air quality (IAQ) risks within university laboratory settings. The framework leverages real‐time monitoring via IQAir AirVisual Pro sensors to continuously track critical IAQ parameters, specifically particulate matter (PM1, PM2.5 ...
Ammar Yaser Abdullah, Ibrahim Abdelfadeel Shaban, Mansoor Mohammed Alnahdi, Hazza Muhsen Abdoul Qader Al Ameri, Nima Izadyar   +4 more
wiley   +1 more source

Efecto de la tasa de compresión en la morfología de grietas de debobinado para chapas de Eucalyptus nitens

Maderas: Ciencia y Tecnología, 2014
El objetivo de este estudio fue evaluar el efecto de tres tasas de compresión (TC) en la morfología de grietas de debobinado en chapas de Eucalyptus nitens para la fabricación de tableros contrachapados.
Andrés Acevedo, Cecilia Bustos, Jean Pierre Lasserre, William Gacitúa   +3 more
doaj  

Intuitionistic Fuzzy TOPSIS‐Based Ranking Alternatives of Machining Performance of Ultrasonic‐Assisted Turning in Fabricated Magnesium Alloys for Sustainability

Journal of Engineering, Volume 2026, Issue 1, 2026.
This study is aimed at optimizing the machining performance of magnesium alloys in ultrasonic‐assisted turning (UAT) by enhancing surface quality, tool life, and overall efficiency while minimizing tool wear and energy consumption. Magnesium alloys were fabricated using a bottom‐pouring stir casting technique with commercial pure magnesium (99.9 ...
S. P. Sundar Singh Sivam, V. G. Umasekar, K. Stalin, Adebayo Samuel Olabisi, S. M. Anas   +4 more
wiley   +1 more source

Shear Wave Optical Coherence Elastography and Structural Analysis of the Postnatal Mouse Cornea through Development

Journal of Biophotonics, Volume 18, Issue 12, December 2025.
This paper investigates the geometrical and biomechanical properties of neonatal eyes at the early stages of development. We found that the corneal thickness is uncoupled from elastic wave speed and that the content and organization of the cornea primarily influence its mechanical properties.
Andrew L. Lopez III, Mohammad Dehshiri, Alexander W. Schill, Salavat Aglyamov, Kirill Larin   +4 more
wiley   +1 more source

EFECTO DE UN ENVEJECIMIENTO ACELERADO MEDIANTE RAYOS UV EN LA PROPAGACIÓN SUPERFICIAL DE GRIETAS DE DEBOBINADO EN TABLEROS CONTRACHAPADOS DE Eucalyptus nitens ULTRAVIOLET RAY AGING EFFECT ON LATHE CHECK SURFACE PROPAGATION IN Eucalyptus nitens Plywood

Maderas: Ciencia y Tecnología, 2013
El objetivo de este estudio fue evaluar el efecto de un envejecimiento acelerado mediante rayos ultravioleta y condiciones ambientales controladas sobre la propagación de grietas de debobinado y agrietamiento superficial, al simular las condiciones de ...
Acevedo Andrés, Cecilia Bustos, Jean Pierre Lasserre, William Gacitua   +3 more
doaj  

Online measurement of veneer lathe checks

, 2015
The present work deals with online lathe checks measurement. It is one of the most critical defects of veneer (leading to handling difficulties, excess of glue consumption, poor veneer surface quality, etc.). It could be characterized by lathe checks depth or frequency but these indicators require tedious measurements of the veneers.
Denaud, Louis, Boukeri, Asma, Krebs, Michael, Butaud, Jean-Claude, Letourneau, Roger   +4 more
openaire   +2 more sources