Results 51 to 60 of about 37,055 (297)
Advances of 2D MoS2 for High-Energy Lithium Metal Batteries
Frontiers in Energy Research, 2021 Often touted as the most promising next-generation energy storage systems, lithium (Li) metal batteries have drawn extensive interest due to their energy densities beyond those of Li-ion batteries.
Eunho Cha +3 more
doaj +1 more source
????????? ??????????????? ?????? ??????????????? ?????? ??????????????? [PDF]
, 2018 Department of Energy Engineering (Battery Science and Technology)The continuous throng in demand for high energy density rechargeable batteries innovatively drives technological development in cell design as well as electrochemically active materials. In
Jeong, Dae-Hyeon
core
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced ScienceLi and Zn metals are considered promising negative electrode materials for the next generation of rechargeable metal batteries because of their non‐toxicity and high theoretical capacity.
Yunyu Zhao, Kaiyong Feng, Yingjian Yu
doaj +1 more source
, 2011 Cycling efficiency and rate capability of porous copper-coated, amorphous silicon thin-film negative electrodes are compared to equivalent silicon thin-film electrodes in lithium-ion batteries. The presence of a copper layer coated on the active material
Kowolik, Kristin +2 more
core +1 more source
Microbial Communities and Electrochemical Performance of Titanium-Based Anodic Electrodes in a Microbial Fuel Cell [PDF]
, 2011 Four types of titanium (Ti)-based electrodes were tested in the same microbial fuel cell (MFC) anodic compartment. Their electrochemical performances and the dominant microbial communities of the electrode biofilms were compared.
Michaelidou, U. +5 more
core +4 more sources
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Nanobead-reinforced outmost shell of solid-electrolyte interphase layers for suppressing dendritic growth of lithium metal [PDF]
, 2018 Department of Energy EngineeringDesign of catalyst support for high durability of oxygen electrocatalystPlating-stripping reversibility of lithium metal was improved by reinforcing the solid-electrolyte interphase (SEI) layer by inorganic nanobeads ...
Kim, Minsoo
core
The Joint Center for Energy Storage Research: A New Paradigm for Battery Research and Development
, 2015 The Joint Center for Energy Storage Research (JCESR) seeks transformational change in transportation and the electricity grid driven by next generation high performance, low cost electricity storage.
Crabtree, George
core +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source