Results 241 to 250 of about 22,309 (312)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Safety boundary protection control for distributed propulsion vehicle operating in plateau environment. [PDF]

Sci Rep
Dong Z, Da X, Zhang B, Guo L.
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

An accelerating inverted wing with ground effect: downforce measurement and reconstruction. [PDF]

Exp Fluids
Zhou S, Overmars EFJ, Westerweel J.
europepmc   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Biomechanical insights into increasing jump distance in ski jumping: a review classified by hill size. [PDF]

Front Sports Act Living
Funato Y, Sakurai S.
europepmc   +1 more source

Sezawa-Mode Surface Acoustic Wave Resonators in Pulsed-Laser-Deposited Pb_0.9Ba_0.1(Zr_0.52,Ti_0.48)O₃ on Bulk Silicon. [PDF]

Micromachines (Basel)
Janssens Y, Berenschot E, Nguyen M, Tas N.   +3 more
europepmc   +1 more source

PENGARUH TIPE PROTOTYPE SEPEDA MOTOR TERHADAP COEFFICIENT DRAG DAN LIFT PADA OPEN CIRCUIT WIND TUNNEL

Achmad Masum Nur Aini, Muhamad Hanifudin, Dony Perdana   +2 more
openalex   +2 more sources

Enhancing aerodynamic performance using biomimetic wavy trailing edges on aircraft wing at low Reynolds number. [PDF]

Sci Rep
Aziz MA, Khalifa MA, Elshimy H, Elsayed AM.   +3 more
europepmc   +1 more source

Predictive modelling of drag, lift and torque coefficients of cylindrical biomass particles under artificial intelligence

Jingliang Wang, Qingyan Fang
openalex   +2 more sources