Results 51 to 60 of about 11,144,592 (297)
Evaluation of MEMS Structures with Directional Characteristics Based on FRAT and Lifting Wavelet [PDF]
Steps and grooves, which have typical directional characteristic, are two main functional structures of MEMS (Micro-Electro-Mechanical Systems). This paper proposes a method for analysis and evaluation of MEMS steps and grooves based on finite radon ...
Li, Tukun +7 more
core +1 more source
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich +3 more
wiley +1 more source
This paper aims to address the problems of aerial orientation control and safety in sudden extreme working conditions during the integral intelligent lifting of large-span heavy steel box girder. Based on the project of Xiaotun Bridge of Fuyi Expressway,
Xiaofeng Liu +5 more
doaj +1 more source
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik +9 more
wiley +1 more source
Research on Towing Stability of Composite Bucket Foundation for Offshore Wind Power Generation
[Introduction] As the foundation of one-step transportation and installation technology, composite bucket foundation of offshore wind power generation has been widely used in the development of offshore wind power. The main research content of this paper
NI Daojun, XIAO Yaoyao
doaj +1 more source
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone +11 more
wiley +1 more source
Finite Element Simulations of the Sinus Lifting Process
In the current market, the rotary sinus lift approach is developed by many manufacturers to substitute for the traditional osteotome technique. Sinus lift surgery can be achieved safely and accurately by using the rotary sinus lift approach.
Li Wen Chen +4 more
core +1 more source
In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa +19 more
wiley +1 more source
Design of 6-DOF Tomato Picking Lifting Platform
The tomato picking lifting platform is the carrier for the installation of the picking manipulator, which directly affects the operating range, speed, and picking effect of the picking manipulator. Based on the six degree of freedom motion platform, this
Pei Cao +5 more
doaj +1 more source
Integration of Low‐Voltage Nanoscale MoS2 Memristors on CMOS Microchips
This article presents the first monolithic integration of nanoscale MoS2‐based memristors into the back‐end‐of‐line of foundry‐fabricated CMOS microchips in a one‐transistor‐one‐resistor (1T1R) architecture. The MoS2‐based 1T1R cells exhibit forming‐free, nonvolatile resistive switching with ultra‐low operating voltages, low cycle‐to‐cycle variability ...
Jimin Lee +16 more
wiley +1 more source

