Results 41 to 50 of about 367,216 (307)
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Lightweight Aluminum–FRP Crash Management System Developed Using a Novel Hybrid Forming Technology
VehiclesThe one-step hybrid forming process is a novel process to fabricate a metal fiber-reinforced plastic (FRP) structure with reduced cycle time and cost compared to classical multi-step methods. It is realized by a combined forming tool for both sheet metal
Amir Hajdarevic +3 more
doaj +1 more source
Comparison of different microCT-based morphology assessment tools using human trabecular bone
Bone Reports, 2020 MicroCT-based morphological parameters are often used to quantify the structural properties of trabecular bone. Various software tools are available for calculating these parameters. Studies that examine the comparability of their results are rare.
Lukas Steiner +2 more
doaj +1 more source
Solar cell submodule design facilitates assembly of lightweight arrays [PDF]
, 1966 Solar cell submodules with bus bars that leave tabs along one end of the submodule and wires with raised portions along the other end are assembled by interlocking the tabs and wires of adjacent submodules.
Yasui, R. K.
core +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Attribute dependency graphs: modelling cause and effect in systems design
Design Science, 2022 Complexity in product design increases with little understanding of cause and effect. As a consequence, the impact of design decisions (or changes) on the product is difficult to predict and control.
Sebastian Rötzer +3 more
doaj +1 more source
NEWS: the near-infrared Echelle for wideband spectroscopy [PDF]
, 2016 We present an updated optical and mechanical design of NEWS: the Near-infrared Echelle for Wide-band Spectroscopy (formerly called HiJaK: the High-resolution J, H and K spectrometer), a compact, high-resolution, near-infrared spectrometer for 5-meter ...
Hall, Zachary +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced concentrator panels [PDF]
, 1981 The prototype fabrication of a lightweight, high-quality cellular glass substrate reflective panel for use in an advanced point-focusing solar concentrator was completed. The reflective panel is a gore shaped segment of an 11-m paraboloidal dish.
Bedard, R. J., Jr., Bell, D. M.
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source