Results 91 to 100 of about 614,448 (304)
The mechanics of film cooling-Part 1 [PDF]
, 1954 Thin liquid wall films flowing under the influence of high-velocity turbulent gas streams were studied for the purpose of obtaining an understanding of the mechanics of film cooling.
Knuth, Eldon L.
core +3 more sources
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Analysis of systems for cooling liquid injection in turbine engine gas flow duct
Авіаційно-космічна техніка та технологіяThe subject of this article is a system for cooling liquid injection in gas flow duct of aviation gas-turbine engine (GTE). The goal is to soften the acuteness of contradictions between economic and ecological requirements; ecological requirements and ...
Ruslan Tsukanov, Sergii Yepifanov
doaj +1 more source
Heat Dissipation for Microprocessor Using Multiwalled Carbon Nanotubes Based Liquid
The Scientific World Journal, 2013 Carbon nanotubes (CNTs) are one of the most valuable materials with high thermal conductivity (2000 W/m·K compared with thermal conductivity of Ag 419 W/m·K).
Bui Hung Thang +4 more
doaj +1 more source
The boiling suppression of liquid nitrogen
, 2009 When He gas is injected from room temperature into boiling liquid N$_{2}$, boiling is suppressed, leaving liquid surface flat like a mirror. Although the qualitative explanation for this phenomenon is known [Minkoff G J \textit{et al}.
H. Fukuyama +5 more
core +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Liquid-cooling technology for gas turbines review and status [PDF]
A review of research related to liquid cooling of gas turbines was conducted and an assessment of the state of the art was made. Various methods of liquid cooling turbines were reviewed.
Stepka, F. S., Vanfossen, G. J., Jr.
core +1 more source
Thermo-mechanical analysis of additively manufactured hybrid extrusion dies with conformal cooling channels [PDF]
, 2019 Profile overheating and surface defects during hot aluminum extrusion can occur when seeking higher productivity rates at increased ram speed velocities. The incorporation of cooling channels in the die-design allows overcoming this process limitation by ...
Bertoli, C., Hora, P., Stoll, P.
core
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source