Results 151 to 160 of about 796,368 (357)

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Fatigue life time modelling of Cu and Au fine wires

MATEC Web of Conferences, 2018
In this study, the influence of microstructure on the cyclic behaviour and lifetime of Cu and Au wires with diameters of 25μm in the low and high cycle fatigue regimes was investigated.
Khatibi Golta, Mazloum-Nejadari Ali, Lederer Martin, Delshadmanesh Mitra, Czerny Bernhard   +4 more
doaj   +1 more source

Experimental and Numerical Modal Analysis of Composite Sandwich Structures Using Surfboards as Model Systems

Advanced Engineering Materials, EarlyView.
This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan, Luca Lomazzi, Mathis Mercier, Kara Stark, Marc in het Panhuis   +4 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

TS SPECIMEN LIFE PREDICTION OF HIGH-STRENGTH STEEL RESISTANCE SPOT WELDS

Jixie qiangdu, 2016
The plastic zone in crack tip influences life prediction result when using crack propagation method to predict fatigue life of spot welds. Most of the methods used to predict fatigue life don’t take plasticity into consideration.
ZHANG Yu, LI DaYong, TANG WeiQin
doaj  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

High temperature creep and fatigue crack growth in alloy 800H

, 2022
S.655-660The present paper reports experimental work directed towards the analysis of the potential of various crack growth correlating parameters to describe low cycle fatigue and creep crack growth in Alloy 800H at 800 degrees C.
Bressers, J., Hollstein, T., Weise, W.
core  

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Texoskeletons: Developing the Fundamental Technologies for Creating Intelligent Soft Robotic Clothing With Integrated 1D Sensors and Actuators

Advanced Functional Materials, EarlyView.
ABSTRACT Traditional wearable exoskeletons rely on rigid structures, which limit comfort, flexibility, and everyday usability. This work introduces the fundamental technologies to create the first soft, lightweight, intelligent textile‐based exoskeletons (Texoskeletons) built using 1D sensors and actuators.
Amy Lukomiak, Rameesh Bulathsinghala, Jack Varga, Shuxin Meng, Kalana Marasinghe, Imaad Refai, Biyon Fernando, Amitkumar Patel, Chamika M. Halloluwa‐Arachchige, Carlos Oliveira, Arash M. Shahidi, Zahra Rahemtulla, Alexander Turner, Ziyun Ding, Bernard X. W. Liew, Andy Kerr, Ezio Preatoni, Theo Hughes‐Riley, Ishara Dharmasena, Pasindu Lugoda   +19 more
wiley   +1 more source