Results 71 to 80 of about 6,037 (261)

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Characteristics and Formation of a Synoptic Situation Causing Sudden Turning of Mesoscale Convective Systems over South China

Atmosphere, 2019
The characteristics and formation of a synoptic situation that causes a sudden turning motion of warm-sector mesoscale convective systems (MCSs) over South China are described, based on the collection and investigation of associated cases during April ...
Zhaoming Liang, Ying Liu, Jinfang Yin
doaj   +1 more source

Optimization of the Production of Rubber Compounds Using Mathematical Models

Advanced Engineering Materials, EarlyView.
Rubber compounds were mixed in a batch internal mixer, and symbolic regression was used to derive mathematical models linking recipe and process parameters to ram path, torque, and mixing quality (incorporation, dispersion, distribution). Subsequent optimization with evolutionary algorithms identified operating conditions that reduce specific energy ...
Anke Bardehle, Andreas Limper, Ulrich Giese, Carlos Lucke, Mario Beiner, Christoph Gögelein, Lisa Leuchtenberger‐Engel, Christian Hopmann   +7 more
wiley   +1 more source

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

Comparative Study of Low-Level Wind Fields Characteristics at Two Critical Locations in the Terminal Area of Plateau Mountain Airports During the Dry-Season Using Coherent Doppler Wind Lidars

Remote Sensing
The Qinghai–Tibet Plateau is characterized by highly complex terrain, and civil aviation serves as a primary mode of transportation for regional mobility.
Junjie Wu, Zhuoqun Shi, Mingrui Lu, Xiaojing Li, Tinglong Zhang, Wanyin Luo   +5 more
doaj   +1 more source

Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures

Advanced Engineering Materials, EarlyView.
We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann, Ryan Kalgreen, Laura M. Comella   +2 more
wiley   +1 more source

Upper limit for wind shear in stably stratified conditions expressed in terms of a bulk Richardson number

Meteorologische Zeitschrift, 2017
Profile measurements of wind and potential temperature from a land site (obtained by a RASS for several years) and an offshore site (obtained at the meteorological mast on the research platform FINO 1 for one year) are used to analyse the temporal ...
Stefan Emeis
doaj   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source