Results 161 to 170 of about 10,778,698 (292)

Parametrically Engineered Laser-Induced Graphene with Tunable Electrical and Morphological Properties for Flexible Sensor Applications. [PDF]

ACS Omega
Beigh FT, Beigh NT, Mallick D.
europepmc   +1 more source

High‐Entropy Alloy Interlayers Toward Advanced Joining for High‐Performance Structural Applications: Current Progress and Emerging Challenges

Advanced Engineering Materials, EarlyView.
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan, Jiafen Song, Jinglong Li, Jiangtao Xiong, Tao Yang   +4 more
wiley   +1 more source

Thermal fluid coupling simulation and optimization of downhole baffle heater adapted to Tar-rich Coal in-situ pyrolysis. [PDF]

Sci Rep
Shuai Z, Jiaying S, Peng W, Zhongjin S.
europepmc   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Flexible microscale tactile display with liquid-to-gas phase-change actuator array. [PDF]

Microsyst Nanoeng
Sim S, Bae K, Hwang K, Koh S, Kim J.
europepmc   +1 more source

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

Advanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source

The Parameters and Applicability Analysis of Low Calorific Value Gases Applied to Oil Shale In Situ Conversion Catalytic Combustion Heaters. [PDF]

ACS Omega
Shui H, Liu S, Liu Z, Zhang K, Li L, Zhao K.   +5 more
europepmc   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

Increase of energy efficiency in the low-pressure heater of PN-1100-25-6-1 type

Journal of Physics: Conference Series, 2017
V.I. Velichko, N. N. Trofimenko, V. A. Milyutin   +2 more
openaire   +1 more source

Waste Pressure Energy Recovery System: Life Cycle Analysis (LCA) Report: General Technology

This report analyzed the life cycle environmental impacts, primarily the life cycle GHG emissions of a waste pressure energy recovery system intended for installation at pressure reduction stations within gas transmission and distribution networks or ...
Gopalakrishnan, Varun, Giardinella, Sebastiano   +1 more
core