Results 171 to 180 of about 10,778,698 (292)

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

A fabrication-aware vectorized generative representation for topology optimization of path-defined MEMS microstructures. [PDF]

Microsyst Nanoeng
Liu GZ, Zhao LF, Zhang J, Liu X, Lv YM, Geng TY, Zhou ZF.   +6 more
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Mechanism-to-Deployment Engineering of NO₂ Gas Sensors: Materials, Interfaces, Transducers, and Environmental Validation. [PDF]

Materials (Basel)
Jung D.
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Thermotherapy for Chronic Wounds: A Wound-Interface Translation Framework for Materials, Devices, Clinical Evidence, and Validation Requirements. [PDF]

Bioengineering (Basel)
Ahmad Hasan S, Al-Naami B, Al-Ayyad M, Al-Hinnawi AR, Korostynska O.   +4 more
europepmc   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Vortex-mediated spin current injection into two-dimensional superconductor NbSe₂. [PDF]

Sci Adv
Yang M, Yin X, Liu J, Chen Y, Gao Q, Zhu H, Huang D, Chen L, Yang SY, Li J.   +9 more
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Thermal and moisture characteristics of air from a galvanized steel tubular solar air heater for potential drying applications. [PDF]

Sci Rep
Ahmed HA, Al-Ghaithy AE, Al-Mashriqi SA, Othman MB, Ahmed AM, Al-Koul SM.   +5 more
europepmc   +1 more source