Results 101 to 110 of about 15,296,121 (237)
Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner +7 more
wiley +1 more source
Boosters or building renovations? An evaluation of 4th generation district heating strategies
Decarbonising the urban heating sector is critical for achieving sustainable cities. Low-Temperature District Heating offers a promising pathway, yet its implementation in existing unrenovated buildings presents significant challenges.
Luca Casamassima, Lukas Kranzl
doaj +1 more source
Background District heating systems have been gaining importance in the last years. However, local circumstances, e.g. regarding heat demand and available heat sources, are diverse and new technologies especially in the low-temperature sector arise ...
Franz Zach +2 more
doaj +1 more source
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan +4 more
wiley +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar +3 more
wiley +1 more source
Conceptual study of a solar-assisted low-temperature district heating substation
At present, the viability of Low-Temperature District Heating (LTDH) systems has already been tested and demonstrated. Even so, for LTDH to be successfully implemented, further ideas are needed in order to improve the flexibility and effectiveness.
Castro Flores, José Fiacro, +4 more
core
Achieving low return temperature for domestic hot water preparation by ultra-low-temperature district heating [PDF]
District heating (DH) is a cost-effective method of heat supply, especially to area with high heat density. Ultra-low-temperature district heating (ULTDH) is defined with supply temperature at 35-45 degrees C.
Svend Svendsen +3 more
core +1 more source
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika +5 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source

