Results 51 to 60 of about 51,245 (254)

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Comprehensive Noise Modeling of Piezoelectric Charge Accelerometer with Signal Conditioning Circuit

Micromachines
This paper reports on noise modeling of a piezoelectric charge accelerometer with a signal conditioning circuit. The charge output is converted into voltage and amplified using a JFET operational amplifier that has high input resistance and low noise ...
Ghulam Ali, Faisal Mohd-Yasin
doaj   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Low-Noise Multimodal Reconfigurable Sensor Readout Circuit for Voltage/Current/Resistive/Capacitive Microsensors

Applied Sciences, 2020
This paper presents a low-noise reconfigurable sensor readout circuit with a multimodal sensing chain for voltage/current/resistive/capacitive microsensors such that it can interface with a voltage, current, resistive, or capacitive microsensor, and can ...
Donggeun You, Hyungseup Kim, Jaesung Kim, Kwonsang Han, Hyunwoo Heo, Yongsu Kwon, Gyungtae Kim, Woo Suk Sul, Jong Won Lee, Boung Ju Lee, Hyoungho Ko   +10 more
doaj   +1 more source

Highly Sensitive Electrochemical Biosensor Based on Hairy Particles with Controllable High Enzyme Loading and Activity

Advanced Functional Materials, EarlyView.
For the first time, a highly sensitive electrochemical biosensor based on SiO2‐based hairy particles with a grafted PDMAEMA polymer brush containing a quantifiable and large amount of immobilized Laccase is reported. The fabricated biosensor exhibits a sensitivity of 0.14 A·m⁻¹, a limit of detection (LOD) of 0.1 µm, and a detection range of 0.3–750 µm,
Pavel Milkin, Anila Antony, Hongtao Cai, Antonia Debevc, Ceyda Topal, Anne Linhardt, Alla Synytska, Leonid Ionov   +7 more
wiley   +1 more source

Low Noise Programmable DC Amplifier with Remote Control

Известия высших учебных заведений России: Радиоэлектроника, 2019
Introduction. The developmental direction of information-measuring systems used to record, pre-process and analyse excess low-frequency noise (flicker noise) in modern experimental technology is well known.
Viktor E. Ivanov, Chye En Un
doaj   +1 more source

Substrate Stress Relaxation Regulates Cell‐Mediated Assembly of Extracellular Matrix

Advanced Functional Materials, EarlyView.
Silicone‐based viscoelastic substrates with tunable stress relaxation reveal how matrix mechanics regulates cellular mechanosensing and cell‐mediated matrix remodelling in the stiff regime. High stress relaxation promotes assembly of fibronectin fibril‐like structures, increased nuclear localization of YAP and formation of β1 integrin‐enriched ...
Jonah L. Voigt, Jens Timmer, Elisabetta Ada Cavalcanti‐Adam   +2 more
wiley   +1 more source

A 2.4/5.2-GHz Concurrent Dual-Band CMOS Low Noise Amplifier

IEEE Access, 2017
A concurrent dual-band low-noise amplifier (LNA) targeted for W-LAN IEEE 802.11 a/b/g standards is designed using 0.13-μm CMOS process. To attain the power-constrained simultaneous noise and input matching at 2.4 and 5.2 GHz, cascode common source
Sami Sattar, Tun Zainal Azni Zulkifli
doaj   +1 more source