Results 71 to 80 of about 80,852 (303)
An evaluation of weld metal nitrogen retention and properties in 316NL austenitic stainless steel [PDF]
, 2011 A series of tests were conducted using varying levels of nitrogen and helium in a conventional argon shielding gas when welding 316LN austenitic stainless steel. The outcome was that a 15 per cent nitrogen addition to the argon shielding gas had the most
Baker, Thomas +2 more
core +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Toughened uni-piece fibrous insulation [PDF]
, 1992 A porous body of fibrous, low density silica-based insulation material is at least in part impregnated with a reactive boron oxide containing borosilicate glass frit, a silicon tetraboride fluxing agent and a molybdenum silicide emittance agent.
Churchward, Rex A. +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Development of 10.9 Grade 32CrB4 Quenched and Tempered Round Steel for Fasteners [PDF]
TeshugangThere is an urgent need to develop low-cost， high-strength， and toughness grades of steel for domestic wind power fasteners in order to enhance the competitiveness of the industrial chain and fully participate in market competition.
Peng Feng, Li Xu, Li Bopeng, Zhang Yue, Wang Zhanzhong, Guo Shibei
doaj +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Low Temperature Impact Toughness of Hot Rolled Steel Sheet Pile SY390BZ
Teshugang, 2011 Material for test of hot rolled steel sheet pile SY390BZ (% ： 0. 23C, 0.44Si, 0.91Mn, 0.06V, 0.010P 0. 002S) is melted by a 55 kg vacuum induction furnace, cast to Φ170 mm round ingot, rolled to 12 mm sheet with 20% reduction in last flat pass and ...
任安超 +6 more
doaj
Low temperature impact toughness and fracture mechanism of cast QT400-18L ductile iron with different Ni additions [PDF]
China Foundry, 2013 Different contents of Ni (0.3wt.% to 1.2wt.%) were added to the QT400-18L ductile iron to investigate the effect of Ni addition on the impact toughness of cast ductile irons at low temperatures.
Zhang Xinning +2 more
doaj
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Experimental characterization of fibre-reinforced composites improved with nanofibres or nanotubes [PDF]
, 2010 A review is presented on the testing and mechanical properties of continuous fibre reinforced composites modified with nanotubes or nanofibres either dispersed in the resin or grown on the microfibres.
Akkerman, R., Koissin, V., Warnet, L.
core +2 more sources