Results 11 to 20 of about 104,199 (290)
Journal of Applied Clinical Medical Physics, Volume 23, Issue 12, December 2022., 2022 Abstract Positron emission tomography with x‐ray computed tomography (PET/CT) is increasingly being utilized for radiation treatment planning (RTP). Accurate delivery of RT therefore depends on quality PET/CT data. This study covers quality control (QC) procedures required for PET/CT for diagnostic imaging and incremental QC required for RTP.
Ran Klein +7 more
wiley +1 more source
A transient inflammatory response contributes to oxaliplatin neurotoxicity in mice
Annals of Clinical and Translational Neurology, Volume 9, Issue 12, Page 1985-1998, December 2022., 2022 Abstract Objectives Peripheral neuropathy is a relevant dose‐limiting adverse event that can affect up to 90% of oncologic patients with colorectal cancer receiving oxaliplatin treatment. The severity of neurotoxicity often leads to dose reduction or even premature cessation of chemotherapy.
Aina Calls +9 more
wiley +1 more source
Creep Characterization of Inconel 718 Lattice Metamaterials Manufactured by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView., 2023 Herein, the creep characteristics of additively manufactured Inconel 718 metamaterials are investigated. The creep behavior of metamaterials and the effects of microstructural defects are assessed, and the microstructure defects are accurately captured using Kachanov's creep damage model.
Akash Singh Bhuwal +5 more
wiley +1 more source
The influence of position in overlap joints of Mg and Al alloys on microstructure and hardness of laser welds [PDF]
, 2013 Structure and properties of laser beam welding zone of dissimilar materials, AZ31 magnesium alloy and A5754 Aluminum alloy, are investigated. The microstructure and quality of the Mg/Al weld were studied by metallography, microhardness and optical ...
Fatih H. +10 more
core +5 more sources
Notch effects in tensile behavior of AM60 magnesium alloys [PDF]
, 2006 The deformation and failure behavior of an AM60 magnesium alloy was investigated using tensile test on circumferentially notched specimens with different notch radii.
Burg, V +4 more
core +3 more sources
Metals, 2020 The influence of alloying elements Er, Zr, Cu, Si and Zn on the crystallization temperature interval, microstructure, mechanical properties and corrosion behavior of Al-Mg-Mn alloy were studied by differential scanning calorimetry (DSC), electron ...
Qianqian Li +5 more
doaj +1 more source
Investigation of Chemical Mechanical Polishing Slurry of magnesium alloy [PDF]
E3S Web of Conferences, 2023 To improve the surface roughness of magnesium alloy, we researched and developed a chemical mechanical polishing (CMP) solution for magnesium alloy, and the effect of sodium tartrate on the surface quality of magnesium alloy and the mechanism of action ...
Zhao Shicheng +2 more
doaj +1 more source
Applied Sciences, 2018 In the present paper, the microstructures of three kinds of in-situ reinforcements Al-Ti-C, Al-Ti-B, and Al-Ti-B-C-Ce were deeply investigated using a combination of scanning electron microscopy, X-ray diffraction spectroscopy, and transmission electron ...
Lusha Tian +7 more
doaj +1 more source
Effects of Additives on the Corrosion Behavior of Magnesium Alloy Electrode in Magnesium Perchlorate Electrolyte [PDF]
Cailiao Baohu, 2022 Aiming at studying the corrosion inhibition effect of different additives on magnesium alloy electrode in magnesium perchlorate electrolyte, the Tafel polarization curve, electrochemical impedance spectroscopy (EIS), surface microscopic morphology and ...
doaj +1 more source
Forgeability of AZ Series Magnesium Alloy produced by Twin Roll Casting [PDF]
, 2017 Plastic forming of magnesium alloy is hardly reported because of its low forgeability. The productions of magnesium alloy are mainly produced by casting. Typical wrought magnesium alloy is AZ31.
Aoki, A. (Atsuhiro) +11 more
core +1 more source