Results 61 to 70 of about 175,789 (264)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Research of the main electromagnetic parameters during the operation of an AC charging station for electric vehicles

open access: yesAvtomobilʹnyj Transport (Harʹkov)
Problem. The increasing popularity of electric cars worldwide is also seen in Ukraine, leading to a growing need for more charging stations. Studies show that 80% of electric car charging happens at home.
Hnatov Andrii   +3 more
doaj   +1 more source

A Study on Magnetic Decoupling of Compound-Structure Permanent-Magnet Motor for HEVs Application

open access: yesEnergies, 2016
The compound-structure permanent-magnet (CSPM) motor is used for an electrical continuously-variable transmission (E-CVT) in a hybrid electric vehicle (HEV).
Qiwei Xu   +4 more
doaj   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

open access: yesAdvanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim   +2 more
wiley   +1 more source

Proposal of a compact magnetically levitated transverse flux permanent magnet linear synchronous motor as a 6-DOF transport carrier

open access: yesThe Journal of Engineering, 2019
In this study, a novel 6-degree of freedom compact carrier using magnetically levitated transverse flux permanent magnet linear synchronous motor is proposed and initial design characteristics are analysed.
Salman Ahmed   +3 more
doaj   +1 more source

Magnetization dynamics in magnetically coupled heterostructures [PDF]

open access: yes, 2009
This thesis focusses on the influence of interlayer coupling on the magnetization dynamics of heterostructure systems. This topic has been investigated by time-resolved photoemission electron microscopy (PEEM) using a pump-probe approach. Magnetic and chemical contrast is provided by the illumination with circularly polarized x-rays due to the x-ray ...
openaire   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

open access: yesAdvanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi   +2 more
wiley   +1 more source

Incorporation of Selenium into Sol–Gel‐Derived Bioactive Glass: Influence on Glass Structure, Bioactivity, and its Selective Cytotoxicity

open access: yesAdvanced Engineering Materials, EarlyView.
Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni   +7 more
wiley   +1 more source

Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization

open access: yesAdvanced Engineering Materials, EarlyView.
Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier   +17 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

open access: yesAdvanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy