Results 81 to 90 of about 802,143 (292)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source
Magnetically Coupled Impedance-Source Inverters
IEEE Transactions on Industry Applications, 2012 Z-source inverters are a new class of inverters proposed with output voltage or current buck-boost ability. Despite their general attractiveness, there are some present limitations faced by existing Z-source inverters, most of which are linked to their requirement for low modulation ratio at high input-to-output gain and the presence of an impedance ...
Loh, Poh Chiang, Blaabjerg, Frede
openaire +4 more sources
Magnetoresistance of Granular Ferromagnets - Observation of a Magnetic Proximity Effect?
, 1998 We have observed a superparamagnetic to ferromagnetic transition in films of isolated Ni grains covered by non-magnetic overlayers. The magnetoresistance (MR) of the films was measured as a function of the overlayer thickness.
A. Frydman +26 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay +3 more
wiley +1 more source