Results 111 to 120 of about 43,093 (269)
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi +3 more
wiley +1 more source
In Situ Two‐Dimensional Residual Stress Characterization of Thin Films
An integrated in situ curvature metrology platform combining speckle‐based curvature optical metrology (SCOM) with multi‐beam optical sensors (MOS) enables spatially resolved two‐dimensional curvature mapping of thick sputtered coatings. The SCOM technique provides excellent agreement with MOS while providing an extended measurable curvature range ...
Wai Jue Tan +6 more
wiley +1 more source
Microfabrication of Soft Millirobots Propelled by Low Voltage Electrohydraulic Actuators
Manual layer‐by‐layer assembly is replaced by wafer‐level MEMS batch fabrication for compliant polymer‐based electrohydraulic actuators. The microfabricated devices integrate sacrificially defined microcavities, Parylene‐C‐sealed inlets, and multilayer polymer–metal films.
Shai Shmulevich +2 more
wiley +1 more source
Acoustic waves propagate into the chromosphere, contributing to energy transport and their dynamics. Their upward propagation is restricted to frequencies above the acoustic cutoff frequency.
Takayoshi Oba +39 more
doaj +1 more source
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane +4 more
wiley +1 more source
The results of numerical simulation of the magnetization oscillations induced due to the spin transfer effect in a CoFeB/Cu/CoFeB layered nanostructure with a planar magnetization of the pinned layer, when an electric current flows perpendicular to the ...
A. V. Kukharev, A. L. Daniluyk
doaj
A Hybrid Direct Ink Writing–Digital Light Processing (HDD) strategy decouples material extrusion from shape definition, enabling high‐fidelity additive manufacturing of highly viscous, yield‐stress polymer nanocomposites. Excess ink acts as a removable, self‐supporting scaffold, allowing fabrication of unsupported and embedded complex architectures ...
Shahryar Ramezani Bajgiran +3 more
wiley +1 more source
Liquid Crystal Elastomer Actuator Matrix for Large Area Applications
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani +5 more
wiley +1 more source
Biodegradable and Edible Milli‐Fluidic Logic Circuits
Fully biodegradable and edible fluidic circuits are developed using gelatin‐based valves that operate at low pressure. Logic gates, a one‐bit memory, and a ring oscillator are demonstrated, showing that biodegradable materials can perform computation and control.
Shuhang Zhang +3 more
wiley +1 more source
Programming Actuation in 3D‐Printed Micro‐Architectures via Interfacial Adhesion Control
A two‐phase meniscus‐guided 3D printing method directly fabricates microscale poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and poly(vinyl alcohol) (PVA) bilayers with in situ programmable interfaces. Modulating the meniscus stretching speed switches the interface between separated and bonded states, which controls the mechanical ...
Xiao Huan +13 more
wiley +1 more source

