Results 61 to 70 of about 37,225 (265)

Chemical control of nadimide cure temperature and rate [PDF]

open access: yes, 1985
Polyimide resins suitable for use as composite matrix materials are formed by copolymerization of maleic and norbornenyl endcapped monomers and oligomers.
Lauver, R. W.
core   +1 more source

Dynamic Self‐Clickable Decellularized Matrix Hydrogels for Regulating Vascularity and Enhancing Muscle Regeneration

open access: yesAdvanced Science, EarlyView.
Dynamic decellularized hydrogels are prepared using bovine decellularized small intestine submucosa (SIS) norbornene (dSIS‐NB). Bovine dSIS contained significant amounts of disulfide‐rich fibrillin‐I, enabling ‘self‐clickable’ thiol‐norbornene gelation and spatiotemporal tuning of hydrogel physicochemical properties.
Van Thuy Duong   +4 more
wiley   +1 more source

Self‐Adhesive Conductive Elastomers for Gel‐Free Biopotential Recording

open access: yesAdvanced Electronic Materials, EarlyView.
σPOMaC, a self‐adhesive conductive citrate elastomer incorporating PEDOT:PSS and DBSA, enables gel‐free biopotential electrodes with stable conductivity and intrinsic skin adhesion. The composite exhibits low resistivity (∼ 0.02 Ω·cm), robust electrical performance during repeated use, and reliable on‐body ECG acquisition comparable to Ag/AgCl ...
Kirstie M. K. Queener   +7 more
wiley   +1 more source

Chemical approach for controlling nadimide cure temperature and rate [PDF]

open access: yes, 1984
Polyimide resins suitable for use as composite matrix materials are formed by copolymerization of maleic and norbornenyl endcapped monomers and oligomers.
Lauver, R. W.
core   +2 more sources

Quasi-static and low-velocity impact behavior of intraply hybrid flax/basalt composites [PDF]

open access: yes, 2019
In an attempt to increase the low-velocity impact response of natural fiber composites, a new hybrid intraply woven fabric based on flax and basalt fibers has been used to manufacture laminates with both thermoplastic and thermoset matrices.
Antonucci, Vincenza   +8 more
core   +1 more source

Excipient Emulsion–Based Delivery Systems for Enhancing Carotenoid Bioavailability: Advances in Formulation and Gastrointestinal Fate

open access: yesAgriFood: Journal of Agricultural Products for Food, EarlyView.
Excipient emulsion systems improve carotenoid solubilization, protect against degradation, and enhance gastrointestinal absorption through optimized formulation and digestion behavior. ABSTRACT Carotenoids are bioactive compounds that contribute to human health through antioxidant, provitamin A, and disease‐preventive effects.
Tugce Ceyhan   +3 more
wiley   +1 more source

Chemical approach for controlling nadimide cure temperature and rate with maleimide [PDF]

open access: yes, 1985
Polyimide resins suitable for use as composite matrix materials are formed by copolymerization of maleic and norbornenyl endcapped monomers and oligomers.
Lauver, R. W.
core   +2 more sources

Impact behaviour of nylon-rubber blends: 5. Influence of the mechanical properties of the elastomer [PDF]

open access: yes, 1989
Blends of 90wt% nylon-6 and 10wt% impact modifier were prepared. As impact modifiers were used: EPDM (ethylene propylene diene monomer) rubber, EPM (ethylene propylene monomer) rubber, polyethylene, four poly(ether esters) and some commercial impact ...
Borggreve, R.J.M.   +2 more
core   +3 more sources

Enhancing of catalytic properties of vanadia via surface doping with phosphorus using atomic layer deposition [PDF]

open access: yes, 2015
This article may be downloaded for personal use only. Any other use requires prior permission of the author and AIP Publishing. This article appeared in J. Vac. Sci. Technol.
Drieß, Matthias   +7 more
core   +2 more sources

High Density Polyethylene/Ground Tire Rubber Composites Compatibilized by Dicumyl Peroxide

open access: yesJournal of Applied Polymer Science, EarlyView.
ABSTRACT In this study, the thermal behavior of dicumyl peroxide (DCP) was first evaluated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), which confirmed a peak decomposition temperature around 172°C, highlighting its incompatibility with standard melt‐mixing techniques for most polyolefins. To overcome this limitation,
Hibal Ahmad, Denis Rodrigue
wiley   +1 more source

Home - About - Disclaimer - Privacy