Results 141 to 150 of about 172,422 (234)

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Efficient Process Development for Laser Powder Bed Fusion of a Soft‐Magnetic Metallic Glass Composite

Advanced Engineering Materials, EarlyView.
Iron‐based metallic glass alloys exhibit excellent soft‐magnetic properties, and unprecedented geometrical freedom in the design of soft‐magnetic metallic glass components is made possible by additive manufacturing. An efficient workflow for developing parameters for laser‐based powder bed fusion of a Fe‐based metallic glass alloy is presented along ...
Julia Löfstrand, Priyanka Saha, Vidhiaza Leviandhika, Urban Wiklund, Alexander Elsen, Carolin Zintel, Lena Thorsson, Petra E. Jönsson   +7 more
wiley   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

Simplicity and Complexity in Combinatorial Optimization. [PDF]

Entropy (Basel)
Dingle K, Hutter M.
europepmc   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

An in-depth analysis of UAV path planning, including procedures, algorithms, optimization models, and emerging challenges. [PDF]

MethodsX
Nafees M, Syeda T, Ali A, Farman H, Tayyab M.   +4 more
europepmc   +1 more source

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, EarlyView.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source

Near real-time full-wave inverse design of electromagnetic devices. [PDF]

Nat Commun
Sun JH, Elsawaf M, Zheng Y, Lin HC, Hsu CW, Sideris C.   +5 more
europepmc   +1 more source