Results 51 to 60 of about 33,754 (277)
Studies and Researches on Heating Microstructures of Some Steels
Scientific Bulletin of Valahia University: Materials and Mechanics, 2022 An important category of widely used steels is chromium alloy improvement steels (STAS 9382/4-89) intended for the execution of shafts, axles, cams, sprockets and sprockets subjected to operation at important demands.
Stoian Elena Valentina +5 more
doaj +1 more source
Effect of Fatigue Crack Growth Rate on Varied Percentage of Martensite for Welded DP Steel [PDF]
, 2013 The objective of this investigation is to study the fatigue behaviour of Dual phase(DP)steel with varying percentage of martensite. The study is conducted on samples of welded Dual phase steel prepared by intercritical ...
Kempaiah, U.N., Nagaraj Kori, .
core
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Mechanical and tribological behavior of dual-phase ductile iron with different martensite amounts
Journal of Materials Research and Technology, 2023 Ferrite-martensite (F/M) dual-phase ductile iron with different relative amounts of martensite was fabricated via intercritical quenching in the present study. The mechanical properties and tribological behavior were investigated. The strength of ductile
Chen Liu +7 more
doaj +1 more source
MARTENSITE TRANSFORMATIONS IN Fe-Pd ALLOYS
, 1982 Martensite transformations in Fe-Pd alloys have been extensively studied by means of X-ray diffractometry, optical and electron microscopy and Mössbauer effect. Successive martensite transformations were found in the Fe-Pd alloys with about 30at% Pd. The
R. Oshima, M. Sugiyama
core +1 more source
Advanced Engineering Materials, EarlyView.This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan +4 more
wiley +1 more source
Hydrogen Effect on the Cyclic Behavior of a Superelastic NiTi Archwire
Metals, 2019 In this work, we are interested in examining the strain rate effect on the mechanical behavior of Ni–Ti superelastic wires after hydrogen charging and ageing for 24 h.
Rihem Sarraj +4 more
doaj +1 more source
Metals, 2020 The wear characteristics of SUS304 and SUS316 stainless steels were evaluated at the rotation speeds of 100 m/s, 200 m/s, and 300 m/s under dry and wet conditions.
Yoon-Seok Lee +2 more
doaj +1 more source
Structure and Phase Transition of Fe-Mn Alloy Powders Prepared by Gas Atomization [PDF]
Materials Research, 2015 In this paper we investigated the microstructure and phase transition of atomized Fe-(1.3, 7.9, 11.7 wt.%) Mn alloy powders. The results show that the main phases of Fe-1.3Mn, Fe-7.9Mn and Fe-11.7Mn powders are ferrite, α’-martensite+austenite, α ...
Yang Yang +4 more
doaj +2 more sources