Results 61 to 70 of about 8,165 (229)

Variant Selection in Fe-20Ni-1.8C under Bending

Crystals, 2018
Variant selection is commonly observed in martensitic steels when a stress is applied to the material during transformation. Classically, the selection phenomenon is modelled considering the work of the shape strain in the applied stress field.
Annick P. Baur, Cyril Cayron, Roland E. Logé   +2 more
doaj   +1 more source

Multi‐Axis Stretchable Zippers for Personalized Wound Healing

Advanced Science, EarlyView.
Multi‐axis stretchable zippers can adapt to complex wound morphologies and enable personalized wound treatment through programmable contraction. This morphological matching strategy helps accelerate wound closure, improve blood perfusion, promote epithelial regeneration, and enhance collagen remodeling, pioneering new directions for personalized and ...
Siyuan Cai, Guang Yao, Zijian Chen, Shiqi Zhou, Peisi Li, Liheng Lin, Huake Yang, Ziyi Zhou, Linbo Jin, Xingyi Gan, Chenzheng Zhou, Zhen Cai, Taisong Pan, Min Gao, Dongli Fan, Yuan Lin, Yiming Zhang   +16 more
wiley   +1 more source

Fracture of drilling head pipe connection due to quenching of heat affected zone (HAZ)

Metalurgija, 2015
The drilling head pipe connection is made of quenched and tempered steel 34CrNiMo6. The steel characteristic is high hardenability. Due to unsuitable and untested welding technology the heat affected zone (HAZ) cooling rate after welding surpassed the ...
B. Zorc, M. Bizjak, B. Kosec, A. Nagode
doaj  

Smart Bioinspired Material‐Based Actuators: Current Challenges and Prospects

Advanced Intelligent Systems, Volume 7, Issue 3, March 2025.
This work gathers, in a review style, an extensive and comprehensive literature overview on the development of autonomous actuators based on synthetic materials, bringing together valuable knowledge from several studies. Furthermore, the article identifies the fundamental principles of actuation mechanisms and defines key parameters to address the size
Alejandro Palacios, Léon Chiriatti, Simon Poppinga, Thomas Speck, Vincent Le Houérou   +4 more
wiley   +1 more source

A Review on Recent Trends of Bioinspired Soft Robotics: Actuators, Control Methods, Materials Selection, Sensors, Challenges, and Future Prospects

Advanced Intelligent Systems, Volume 7, Issue 3, March 2025.
This article reviews the current state of bioinspired soft robotics. The article discusses soft actuators, soft sensors, materials selection, and control methods used in bioinspired soft robotics. It also highlights the challenges and future prospects of this field.
Abhirup Sarker, Tamzid Ul Islam, Md. Robiul Islam   +2 more
wiley   +1 more source

Active Stiffness Modulation of Flexible PDMS Elastomer by Embedding Shape Memory Alloy Wires: Fabrication and Modeling

FlexTech, EarlyView.
Active stiffness modulation is achieved in NiTi shape memory alloy‐reinforced PDMS and carbon fiber‐epoxy composites, with reversible 3‐fold modulus increase via Joule heating and validated predictive models, which resolves longstanding adaptive design challenges.
Xi Yi, Dongjie Jiang
wiley   +1 more source

Effect of Heat Treatment Parameters on Microstructure, Hardness, and Corrosion Resistance of Martensitic Stainless Steel X30Cr13 (AISI 420B)

Materials and Corrosion, EarlyView.
The hardness and corrosion resistance of the martensitic stainless steel X30Cr13 depend directly on the applied heat treatment. This article describes and discusses the relationships between alloy composition, thermodynamic phase stabilities, heat treatment parameters, resulting microstructures, and achievable corrosion resistance. To investigate these
Adrian Evia Ocampo, Saskia Roßberg, Jann Rohr, Paul Rosemann   +3 more
wiley   +1 more source

Influence of Strain Rate on the Strain Hardening Behavior of a Lean Duplex Stainless Steel

MetalMat, EarlyView.
The aim of this study was to examine how strain rate influences the compressive strain‐hardening behavior of a lean duplex stainless steel LDX 2101. Microstructural analysis using electron backscatter diffraction (EBSD) revealed a strain‐induced austenite‐to‐martensite transformation.
Akilakps Sawyerr, Eric Kotei T. Addison, Martin Owusu‐Mensah, Abdul Jaleel Mohammed, Daolun Chen   +4 more
wiley   +1 more source

Comparative Characteristics of Martensite and Bainite in Cu-Based SMAs

The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2014
The present work reports the evolution of micro-structure and shape memory behavior in a Cu-15 Zn-6 Al (mass. %) shape memory alloy (SMA), as a function of the applied hot working procedure and of the performed heat treatments.
Elena MIHALACHE, Monica-Nicoleta LOHAN, Bogdan PRICOP, Leandru-Gheorghe BUJOREANU, Marius-Gabriel SURU   +4 more
doaj  

Semantic Embeddings of Chemical Elements for Enhanced Materials Inference and Discovery

Materials Genome Engineering Advances, EarlyView.
ElementBERT extracts semantic embeddings of chemical elements from 1.29 million alloy‐related abstracts, providing robust descriptors that improve prediction accuracy by up to 23% across titanium, high‐entropy, and shape memory alloys, with demonstrated generalization on alloy compositions reported in 2025.
Yunze Jia, Yuehui Xian, Yangyang Xu, Pengfei Dang, Xiangdong Ding, Jun Sun, Yumei Zhou, Dezhen Xue   +7 more
wiley   +1 more source