Results 121 to 130 of about 59,771 (215)

Towards environmental management of WEEE in Brazil: evaluating the impacts of recycling plastics. [PDF]

Environ Sci Pollut Res Int
da Silva AFS, de Freitas GA, Silva DAL, de Paiva JMF, Campolina JM, da Silva Moris VA.   +5 more
europepmc   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Fracture Toughness and Failure Mechanisms of Glass-Reinforced Plastics Based on an Epoxy Matrix Modified with Polysulfone and an Active Diluent. [PDF]

Polymers (Basel)
Petrova TV, Tretyakov IV, Alexeeva OV, Sergeev AY, Korokhin RA, Solodilov VI, Yurkov GY, Berlin AA.   +7 more
europepmc   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

From Environmental Burden to Energy Resource: Waste Plastic-Derived Carbons for Sustainable Batteries and Supercapacitors. [PDF]

Polymers (Basel)
Kitchamsetti N, Mhin S, Han H, de Barros ALF.   +3 more
europepmc   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Toxic Substances in Plastics, Micro- and Nanoplastics: Utilizing ATSDR's Plastics-Related Toxicological Profile Tool and Mixtures Framework for Human Health Risk Assessment. [PDF]

Toxics
Muianga CV, Zarus GM, Stallings K, Casillas G, Shoeb M, Gehle K, Mumtaz MM, Reh CM.   +7 more
europepmc   +1 more source

High‐Temperature Phase Transformation in a V‐9Si‐6.5B Alloy: The Kinetic and Crystallographic Pathway From V5SiB2 to V8SiB4

Advanced Engineering Materials, EarlyView.
In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti, Andreas Stark, Roja Rani Korrayi, Florian Pyczak, Georg Hasemann   +4 more
wiley   +1 more source

Evaluation of the Efficiency of Biological Treatment in Activated Sludge from a WWTP at Laboratory Scale for the Elimination of Biomicroplastics and Related Products. [PDF]

Molecules
Alcaide-Benavides D, Torres-Arévalo E, Farré M, Llorca M.   +3 more
europepmc   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source