Results 61 to 70 of about 80,178 (291)
Materials Research Express, 2021 High-strength steel has excellent mechanical properties and develops rapidly, but the toughness of weld metal cannot be well solved, which hinders the large-scale application of high-strength steel to a certain extent.
Tianli Zhang +5 more
doaj +1 more source
Micro-alloying and the Toughness of Glasses: Modeling with Pinned Particles
, 2013 The usefulness of glasses, and particularly of metallic glasses, in technological applications is often limited by their toughness, which is defined as the area under the stress vs. strain curve before plastic yielding.
Dasgupta, Ratul +3 more
core +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
Metals, 2022 In this work, 35Fe30Cr20Ni10Mo5W (wt.%) and 30Fe30Cr20Ni10Mo10W (wt.%) high-entropy alloys were fabricated using a powder metallurgy route. Powder mixtures for a hot-pressure process were obtained by the mixing and mechanical alloying of elemental ...
Alexander Yurievich Ivannikov +7 more
doaj +1 more source
Mechanical alloying of Cu and Fe induced by severe plastic deformation of a Cu-Fe composite
, 2005 A filamentary composite elaborated by cold drawing was processed by High Pressure Torsion (HPT). The nanostructure resulting from this severe plastic deformation (SPD) was investigated thanks to scanning electron microscopy, transmission electron ...
Pareige, Philippe +2 more
core +4 more sources
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Nano-Crystalline Ultrafine Grain Materials Produced by Mechanical Alloying
Teshugang, 2005 The mechanical alloying is an excellent technology of alloying in solid state witch has good prospects and has been applied successfully to produce nano-crystalline ultrafine grain dispersion strengthened materials,magnetic materials,superconducting ...
何航, 倪红卫, 黄群新
doaj
Modification of as-cast Al-Mg/B4C composite by addition of Zr [PDF]
, 2016 Zirconium was used in Al-Mg/B4C composite to improve compocasting efficiency by increasing particle incorporation. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) results revealed that by addition of zirconium a reaction
Bahremand, M. R. +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source