Results 41 to 50 of about 80,178 (291)
Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]
, 2012 The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
FABRE, Agnès, MASSE, Jean-Eric
core +5 more sources
Formation mechanism of amorphous alloys by mechanical alloying.
DENKI-SEIKO[ELECTRIC FURNACE STEEL], 1991 As a technique in synthesizing an amorphous solid, attention has been directed to the solid state reaction. Here a rapid quenching is no longer required and, instead, a very slow reaction takes place in the course of amorphization. This assures us to provide a unique opportunity in studying how any crystals like fcc and bcc transform into an amorphous ...
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Effect of alloying on mechanical properties of as cast ferritic nodular cast irons [PDF]
, 2012 The development of low temperature applications for ferritic nodular cast irons calls for improved materials in the as cast state, e.g. for off-shore windmills components.
Björkegren LE +13 more
core +3 more sources
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Micro Arc Oxidation of Mechanically Alloyed Binary Zn-1X (X = Mg or Sr) Alloys
Crystals, 2023 The binary Zn-1wt.% X (X = Mg or Sr) alloys prepared by the application of mechanical alloying (MA) combined with powder metallurgy were modified by micro-arc oxidation (MAO) treatment in the 2 g/dm3 KOH aqueous solution at 200 V for 1 min for the ...
Kamil Kowalski +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Mechanically driven alloying and grain size changes in nanocrystalline Fe-Cu powders [PDF]
, 1993 Highly supersaturated nanocrystalline FexCu100-x alloys (10 less-than-or-equal-to x less-than-or-equal-to 95) have been prepared by mechanical alloying of elemental crystalline powders.
Eckert, J. +3 more
core
Structural study of Cu$_{2-x}$Se alloys produced by mechanical alloying
, 2004 The crystalline structures of superionic high temperature copper selenides Cu$_{2-x}$Se ($0 \le x \le 0.25$) produced by Mechanical Alloying were investigated using X-ray diffraction (XRD) technique.
A.A.M. Gasperini +20 more
core +1 more source
Organizational commitment of Vocational College Teachers in Malaysia [PDF]
, 2020 This study aimed to validate factors related to organizational commitment among teachers in vocational colleges in Malaysia. As we know, the commitment given to the organization will make the organization manageable.
Abdul Razzaq, Abdul Rasid +3 more
core