Results 231 to 240 of about 1,012,438 (308)

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, EarlyView.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source

Using a meshless method to investigate the effects of confining pressure on the hydraulic fracturing processes of hydraulic tunnels. [PDF]

Sci Rep
Zhang H, Shi Y, Mu J, Hao R, Qi D, Li W, Zhang B, Yu S.   +7 more
europepmc   +1 more source

ME-EM eNewsBrief, March 2011 [PDF]

, 2011
Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University
core   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Hydro-mechanical damage modeling of water-bearing sandstone using an energy dissipation approach under triaxial stress. [PDF]

Sci Rep
Liu Z, Du B, Zhu H, Jiang Y, Wang T, Chen W, Zhao Y, Wang Y.   +7 more
europepmc   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Development and evaluation of a self-generated foam-resin composite sand consolidation system for offshore oil reservoirs. [PDF]

PLoS One
Jiang M, Tang S.
europepmc   +1 more source

ME-EM eNewsBrief, September 2013 [PDF]

, 2011
Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University
core   +3 more sources

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Mechanical behavior of reservoir bank slope-pile-sheet structures under reservoir operation: Field monitoring and numerical simulation analysis. [PDF]

PLoS One
Cai Z, Wu T, Nie L, Wu Y, Xiang Z, Yang Z, Xu N, Qi F.   +7 more
europepmc   +1 more source