Results 21 to 30 of about 4,267,011 (184)
The Investigation of Press Temperature and Time on Properties of Medium Density Fiberboard Produced From Cotton Stalks Fibers [PDF]
تحقیقات علوم چوب و کاغذ ایران, 2016 The objective of the present study was the utilization of cotton stalk residues for medium density fiberboard production. MDF was produced applying Three press temperatures (170, 180, and 190 oC ) and three pressing times (3,4 and 5 minutes) were used to
Abolfazl Kargarfard, Amir Nourbakhsh
doaj +1 more source
Statistical fatigue experiment design in medium density fiberboard
Materials Research, 2000 Medium Density Fiberboard (MDF) is a wood-based composite widely employed in several industrial applications, in addition to its use in structures subjected to dynamic loads. Its fatigue-related aspects, however, have been consistently ignored. This work
Martínez Espinosa Mariano +1 more
doaj +1 more source
Jurnal Ilmu Pertanian Indonesia, 2023 The scarcity and high cost of high-quality sawn timber has resulted in the switching of furniture industry to using composite wood such as medium density fiberboard (MDF) as the raw material for its products.
Kidung Tirtayasa Putra Pangestu +2 more
doaj +1 more source
Evaluation of Material Properties of Acetylated Medium Density Fiberboard (MDF)
Journal of the Korean Wood Science and Technology, 2020 아세틸화 처리한 라디에타소나무 섬유를 사용하여 제조한 MDF의 수분에 대한 재질 특성을 조사하고 KS F 3200의 섬유판 품질기준과 비교하였다. 아세틸화 처리 MDF는 품질 기준보다 매우 낮은 함수율과 수분 흡수성 및 두께 팽창율을 보여 우수한 치수안정성을 기대할 수 있다. 아세틸화 처리 MDF의 습윤 시 휨강도는 기건 상태 휨강도의 약 70% 이상에 달해 품질 기준에 적합하였다. 아세틸화 MDF의 습윤 시 박리강도가 품질기준의 기건 상태의 최저 박리강도보다 높은 결과를 보여 내수성이 매우 우수하였다. 아세틸화 MDF의 물방울 접촉각은 무처리 MDF에 비하여 커서 낮은 습윤성에 의한 내수성 향상에 기여하는 것으로 판단된다.
Jong Shin LEE, Soung Joon KIM
openaire +2 more sources
Effects of surface lamination process parameters on medium density fiberboard (MDF) properties
BioResources, 2022 Medium density fiberboard (MDF) is widely utilized in furniture production. Most MDF in such applications has a surface laminate layer. The lamination process improves the physical and mechanical properties of the boards. The temperature, press time, and pressure values applied during the lamination process affect such properties.
Özlüsoylu, İsmail +3 more
openaire +3 more sources
Investigating the CO2 laser cutting parameters of MDF wood composite material [PDF]
, 2011 Laser cutting of medium density fibreboard (MDF) is a complicated process and the selection of the process parameters combinations is essential to get the highest quality of the cut section.
Olabi, Abdul-Ghani +5 more
core +2 more sources
Evaluation of Airborne MDF Dust Concentration in Furniture Factories
Floresta e Ambiente, 2017 High concentrations of airborne dust are observed during the cutting of medium density fiberboard (MDF) boards. This dust, at first considered just uncomfortable for workers, may be harmful to their health.
Renilson Luiz Teixeira +5 more
doaj +1 more source
Energetic characterization and radiographic analysis of torrefied coated MDF residues
Scientific Reports, 2021 The use of wood panel residues as biomass for energy production is feasible. Heat treatments can improve energy properties while minimizing the emission of toxic gases due to thermoset polymers used in Medium Density Fiberboard (MDF) panels. Torrefaction
Paula Gabriella Surdi de Castro +6 more
doaj +1 more source
, 2004 Production of fiber composite materials such as Medium Density Fiberboard (MDF) and particleboard (PB) is in general based on wood as a raw material.
Halvarsson, Sören, +2 more
core +8 more sources
Approche comparative des colles d’algues Funori et JunFunori®
CeROArt : Conservation, Exposition, Restauration d'Objets d'Art, 2012 Comparative study between glues produced out of seaweeds, Funoris and JunFunori®, with glues used regularly in conservation treatments. The comparison concernes at first pure glues then secondly, fillings applied to MDF (medium density fiberboard).
Anne-Cécile Dauchez
doaj +1 more source