Results 1 to 10 of about 7,956 (219)

Impact of thermomechanical fiber pre-treatment using twin-screw extrusion on the production and properties of renewable binderless coriander fiberboards [PDF]

, 2017
The aim of this study consisted of manufacturing renewable binderless fiberboards from coriander straw and a deoiled coriander press cake, thus at the same time ensuring the valorization of crop residues and process by-products. The press cake acted as a
Bouvier, Esteves, Evelien Uitterhaegen, Laurent Labonne, Othmane Merah, Philippe Evon, Pintiaux, Sahib, Stokke, Stéphane Ballas, Suchsland, Tajuddin, Thierry Talou, Thierry Véronèse, Van Soest, Van Soest   +15 more
core   +2 more sources

Robust Bayesian target detection algorithm for depth imaging from sparse single-photon data [PDF]

, 2016
This paper presents a new Bayesian model and associated algorithm for depth and intensity profiling using full waveforms from time-correlated single-photon counting (TCSPC) measurements in the limit of very low photon counts (i.e., typically less than 20
Altmann, Yoann, Buller, Gerald S., McCarthy, Aongus, McLaughlin, Steve, Ren, Ximing   +4 more
core   +2 more sources

Utilization of wastes from medium density fiberboards production as an aggregate for lightweight cement composite

MATEC Web of Conferences, 2018
The possibility of recycling waste from medium density fiberboard (MDF) production into wood-cement composites was evaluated. A large quantity of lignocellulosic wastes is generated worldwide from various sources, including wood and furniture industries,
Małaszkiewicz Dorota, Sztukowska Magdalena   +1 more
doaj   +1 more source

Evaluation of Airborne MDF Dust Concentration in Furniture Factories

Floresta e Ambiente, 2017
High concentrations of airborne dust are observed during the cutting of medium density fiberboard (MDF) boards. This dust, at first considered just uncomfortable for workers, may be harmful to their health.
Renilson Luiz Teixeira, José Reinaldo Moreira da Silva, Nilton Cesar Fiedler, José Tarcísio Lima, Paulo Fernando Trugilho, Antônio Carlos Neri   +5 more
doaj   +1 more source

Mechanical and thermal properties of polystyrene and medium density fiberboard composites

Polímeros, 2021
Virgin polystyrene (PS) composites were reinforced with medium density fiberboard (MDF) residue, considering the influence of fiber content. The composites were evaluated for their morphology, identification of functional groups and thermal behavior ...
Juliana Cristina Kreutz, Paulo Ricardo de Souza, Viviane Prima Benetti, Adonilson dos Reis Freitas, Paulo Rodrigo Stival Bittencourt, Luciana Gaffo   +5 more
doaj   +1 more source

X-Ray Tomography To Measure Size Of Fragments From Penetration Of High-Velocity Tungsten Rods [PDF]

, 2012
Behind-armor debris that results from tungsten rods penetrating armor steel at 2 km/s was studied by analysis of recovered fragments. Fragment recovery was by means of particle board. Individual fragments were analyzed by x-ray tomography, which provides
Bless, S., Hanna, R., Levinson, S., McDonald, J., Stone, Z., Tolman, J.   +5 more
core   +1 more source

The use of borax pentahydrate of ınorganıc fıller ın medıum densıty fıberboard productıon

Maderas: Ciencia y Tecnología, 2020
The aim of the study was the use of the inorganic borax pentahydrate mineral in medium density fiberboard production instead of biomass fiber and to specify the performance which physical, mechanical, combustion of produced boards.
Osman Çamlıbel, Mehmet Akgül
doaj  

Image based colorimetric characterization of scrub induced color changes in UV printed and water transfer printed MDF boards

Maderas: Ciencia y Tecnología
Conventional colorimetric evaluation methods remain inadequate for accurately characterizing scrub-induced color changes on UV-printed and water transfer-printed decorative coatings applied to MDF after chemical resistance testing; therefore, this study ...
Mehmet Budakçı, Serdar Kaçamer, Ferzan Katırcıoğlu   +2 more
doaj   +1 more source

Approche comparative des colles d’algues Funori et JunFunori®

CeROArt : Conservation, Exposition, Restauration d'Objets d'Art, 2012
Comparative study between glues produced out of seaweeds, Funoris and JunFunori®, with glues used regularly in conservation treatments. The comparison concernes at first pure glues then secondly, fillings applied to MDF (medium density fiberboard).
Anne-Cécile Dauchez
doaj   +1 more source

Use of nanoparticle in the wood composite to enhance the heat transfer [PDF]

, 2010
The fast growing demand for engineered wood products and development of Medium Density Fiberboard (MDF) leads to numerous research focusing on process parameter and physical properties of the board.
Irawati, Anies, Rachmalina, Rika, Setyawati, Budi   +2 more
core   +1 more source