Results 21 to 30 of about 169,949 (348)
The use of titanium alloys for details of downhole hammers [PDF]
, 2016 The influence of cementation technology of titanium alloy Ti-Al-Mn on its wear resistance is studied. It is established that after lubrication a friction pair with mineral oil the wear resistance of the cemented titanium alloy is comparable to wear ...
Alekseev, S. E. +4 more
core +1 more source
On the Variants of Thermal Process in Developing Strong and Ductile Medium Mn Steel
Frontiers in Materials, 2020 In this contribution, we investigate the influence of three heat treatments, including intercritical annealing (IA), quenching and partitioning (Q&P), and combination of IA and Q&P (IA-Q&P), on microstructure and mechanical properties of the ...
Shuai Pan, Binbin He
doaj +1 more source
Metals, 2023 Twin-roll strip casting (TRSC), which is a low-energy and short process to produce strip steel, is a potential approach to produce advanced high-strength steels.
Cansheng Yu +5 more
doaj +1 more source
Crystals, 2021 Computational simulation has become more important in the design of thermomechanical processing since it allows the optimization of associated parameters such as temperature, stresses, strains and phase transformations.
Ana Claudia González-Castillo +6 more
doaj +1 more source
Strong and ductile medium Mn steel without transformation-induced plasticity effect
Materials Research Letters, 2018 The conventional alloy design of medium Mn steel is to optimize the transformation-induced plasticity (TRIP) effect. Here we show that a dual-phase heterogeneous structure is sufficient to develop a medium Mn steel with high yield strength (∼1.2 GPa) and
B. B. He, M. X. Huang
doaj +1 more source
Cailiao gongcheng, 2023 The MCF-30 testing machine was used to simulate scour of Yellow River Water and Sediment, and the eroding mechanism of high strength and tough medium Mn steel and the relationship of the anti-abrasion performance and mechanical properties with several ...
WEN Qinghua +3 more
doaj +1 more source
Numerical Simulation of Flow and Solidification Behavior of Medium Mn steel in Thin Slab Mold [PDF]
TeshugangThe flow and solidification characteristics of molten steel in thin slab continuous casting mold of medium Mn steel with section of 1 500 mm×90 mm were studied by numerical simulation.
Tian Runyu, Song Bingjun, Peng Zhongyuan, Qiu Yarong, Kong Lingzhong, Yang Jie
doaj +3 more sources
Geabacter species enhances pit depth on 304L stainless steel in a medium lacking with electron donor [PDF]
, 2009 Geobacter sulfurreducens bacteria increased the open circuit potential of 304L stainless steel by around 320 mV in only a few hours after inoculation. This represents a significant increase in the corrosion risk.
Basséguy, Régine +5 more
core +3 more sources
Effect of Q&P Process on 0.15C-MnSi Steels [PDF]
, 2016 The present study is focused on analyzing the effect of Mn amount on two experimental steel compositions, specially designed for Q&P (Quenching and Partitioning), 0.15C-2.5Mn-1.5Si and 0.15C-3Mn-1.5Si without significant contribution of Al.
Cabrera Marrero, José M. +1 more
core +2 more sources
Microfouling of Manganese-oxidizing microorganisms in Rameswaram Coastal Waters. [PDF]
, 2009 Manganese oxidizing marine microorganisms was studied from the coupons of PVC, Titanium, Brass, Copper and Stainless Steel were immersed one meter below water surface, using wooden rafts.
E Kannapiran +2 more
core +2 more sources