Results 101 to 110 of about 70,412 (305)
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Design and Analysis of Double Circular Arc Tooth Profile of Harmonic Drive
Jixie chuandong, 2015 The double circular arc tooth profile of harmonic drive has a significant impact on the performance of gear transmission,based on the kinematics of harmonic gearing theory,the common tangent double circular arc tooth profile that suitable for harmonic ...
Zhou Linyu
doaj
2D Hexagonal Mesh Vs 3D Mesh Network on Chip: A Performance Evaluation
International Journal of Computing and Digital Systems, 2015 D Network on Chip (NoC) has emerged as a new platform to meet the performance requirements and scaling challenges of System on Chip. More investigations require addressing challenges in multiport topologies, minimizing foot printing of nodes and interconnections of wires. This paper discusses multi-port NoC topologies and routing in 2D hexagonal and 3D
openaire +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Analysis of Transient Elastohydrodynamic Lubrication of Asymmetric Polymer Planetary Gears
Jixie chuandong, 2023 Asymmetric polymer gears are used in planetary gear transmission system to cater for the design requirements of compact and lightweight mechanical structure.
Wang Youqiang +4 more
doaj
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
A basis for the analysis of surface geometry of spiral bevel gears [PDF]
, 1983 Geometrical procedures helpful in the fundamental studies of the surface geometry of spiral bevel gears are summarized. These procedures are based upon: (1) fundamental gear geometry and kinematics as exposited by Buckingham, et al; (2) formulas ...
Coy, J. J., Huston, R. L.
core +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source