Results 41 to 50 of about 161,009 (301)
Thermal Performance Assessment of a Double-Pipe Heat Exchanger Utilizing Metal Foam and Nanofluids
Wasit Journal of Engineering SciencesThe current numerical study aims to discover the outcome of the metal foam and nanofluids on the performance of a heat exchanger in contrast with smooth heat exchanger. Water was used as a working fluid at flow rate 2,3,4,5 Lpm.
Mohammed Baqer +3 more
doaj +1 more source
New Approaches to Aluminum Integral Foam Production with Casting Methods
Metals, 2015 Integral foam has been used in the production of polymer materials for a long time. Metal integral foam casting systems are obtained by transferring and adapting polymer injection technology.
Ahmet Güner +2 more
doaj +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Blast resistance of stiffened sandwich panels with closed-cell aluminum foam
Latin American Journal of Solids and StructuresIn the present investigation, response of the stiffened sandwich foam panels with closed-cell aluminum foam cores subjected to blast load is examined. The panels have the metal foam sandwiched between two steel sheets.
Manmohan Dass Goel +2 more
doaj +1 more source
Metallized polymeric foam material [PDF]
, 1974 Open-celled polyurethane foams can be coated uniformly with thin film of metal by vapor deposition of aluminum or by sensitization of foam followed by electroless deposition of nickel or copper.
Bilow, N., Birnbaum, B. A.
core +1 more source
Mechanical properties and energy absorbing capabilities of Z-pinned aluminum foam sandwich [PDF]
, 2019 Aluminum foam sandwich (AFS) structures are suitable for impact protection in lightweight structural components due to their specific energy absorption capability under compression.
Kadkhodapour, Javad +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Impacting device for testing insulation [PDF]
, 1984 An electro-mechanical impacting device for testing the bonding of foam insulation to metal is descirbed. The device lightly impacts foam insulation attached to metal to determine whether the insulation is properly bonded to the metal and to determine the
Redmon, J. W.
core +1 more source
Influence of orientation and radiative heat transfer on aluminum foams in Buoyancy-induced convection [PDF]
, 2015 Two differently-produced open-cell aluminum foams were compared to a commercially available finned heat sink. Further, an aluminum plate and block were tested as a reference. All heat sinks have the same base plate dimensions of four by six inches.
Billiet, MarijnUGent0000901106738020018686019745145821810000-0002-1778-66821D5B7180-F0EE-11E1-A9DE-61C894A0A6B4 +4 more
core +3 more sources