Results 1 to 10 of about 2,381 (168)
Deformation of Fe2Ni prepared by metal powder injection molding
Fenmo yejin jishuIn the process of the metal powder injection molding Fe2Ni, the deformation problem was present due to the uneven distribution of metal powders caused by the poor bonding of binder and shear heat generation.
MU Jianghan +4 more
doaj +2 more sources
Investigation of microstructural evolution of gas-assisted metal injection molded and sintered Mg-0.5Ca alloy [PDF]
Science of Sintering, 2022 In this study, Mg-0.5Ca alloy was produced in a newly designed unit during the metal injection molding process. 40μmD90 Mg powder and 500nmD90 Ca powder were used in accordance with injection molding and powder sintering rules.
Cicek Bunyamin +3 more
doaj +1 more source
Gas Atomization Parametric Study on the VIGA-CC Based Synthesis of Titanium Powder [PDF]
Archives of Metallurgy and Materials, 2020 With the recent advancement in technology for titanium metal powder injection molding and additive manufacturing, high yield and good flowability powder production is needed.
Dae-Kyeom Kim +6 more
doaj +1 more source
Jet Penetration Performance of a Shaped Charge Liner Prepared by Metal Injection Molding
Metals, 2022 The metal injection molding (MIM) method was applied to manufacture a shaped charge liner (SCL) used for petroleum perforating bombs. Its application could overcome the drawback of heterogeneous density distribution prepared using the traditional powder ...
Zheyu He +6 more
doaj +1 more source
Fenmo yejin jishu, 2023 Ultrafine cemented carbides with the different thickness were prepared by metal powder injection molding, using WC–10Co with the particle sizes of 0.71 μm and 0.53 μm as the raw materials and the wax-based binder system as the binders.
LUO Xuequan, LIU Sunhe, WEN Guanghua
doaj +1 more source
Feed Stock Fabrication of AISI 4605 Steel for Fused Deposition Modeling and Sintering and Designing of Its Extruder Mechanism [PDF]
International Journal of Advanced Design and Manufacturing Technology, 2022 Fused Deposition Modeling and Sintering (FDMS) is one of the indirect and emerging processes of Additive Manufacturing (AM) for the production of metal parts, which is a combination of AM process and Metal Injection Molding (MIM).
Amir Rahimi, Jamal Zamani
doaj +1 more source
Analysis of biomedical titanium implant green parts by X-Ray tomography
Journal of Materials Research and Technology, 2021 In this study, X-ray tomography was applied as a non-destructive test to investigate the internal defects of the green part produced with Powder injection molding (PIM).
Levent Urtekin +2 more
doaj +1 more source
Metals, 2021 Low-pressure powder injection molding (LPIM) is a cost-effective technology for producing intricate small metal parts at high, medium, and low production volumes in applications which, to date, have involved ceramics or spherical metal powders. Since the
Atefeh A. Tafti +4 more
doaj +1 more source
Hittite Journal of Science and Engineering, 2017 I n this study, influence of hydrolic pressure or gas pressure on the powder injection molding of 316L stainless steel was investigated. Variations in the microstructure, hardness and density of the porduced samples were discussed in the frame of presure
Yunus Turen
doaj +1 more source
Tehnički Glasnik, 2020 The volumetric flow rate (injection velocity) and the holding pressure are metal injection molding (MIM) parameters that have a strong influence on the green parts density and density homogeneity, but their effect on sintered dimensions after sintering ...
Emir Šarić +2 more
doaj +1 more source