Results 111 to 120 of about 1,340,936 (303)
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Theoretical Calculation of Reorientation Energy in Metal /Semiconductor Interface
Ibn Al-Haitham Journal for Pure and Applied Sciences, 2017 A theoretical calculation of the reorientation energy for non adiabatic electron transfer at interface between metal and semiconductor system was carried out.
H. J. M. A-Agealy, H. Kh. Mujbi
doaj
Spin-transfer in diffusive ferromagnet-normal metal systems with spin-flip scattering
, 2002 The spin-transfer in biased disordered ferromagnet (F) - normal metal (N) systems is calculated by the diffusion equation. For F1-N2-F2 and N1-F1-N2-F2-N3 spin valves, the effect of spin-flip processes in the normal metal and ferromagnet parts are ...
Bauer, Gerrit E. W. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Effect of Metal Foam Structure on Pool Boiling Heat Transfer Characteristics
Zhileng xuebao, 2019 Pool boiling heat transfer characteristics of a refrigerant on heating surfaces of metal foams of different structures were experimentally studied. The test samples were copper foams of different pore densities (5–40 PPI), porosities (0.90 and0.95), and ...
Hu Chenyu +3 more
doaj
Friction and wear behavior of single-crystal silicon carbide in sliding contact with various metals [PDF]
Sliding friction experiments were conducted with single-crystal silicon carbide in contact with various metals. Results indicate the coefficient of friction is related to the relative chemical activity of the metals. The more active the metal, the higher
Buckley, D. H., Miyoshi, K.
core +1 more source