Results 101 to 110 of about 6,181 (222)
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Литьë и металлургия, 2014 Techniques metallographic researches of structure and definition of size of grain of tool steels are offered. The structure of the fast-cutting steel received by a method electroslag remelting from a waste of tool manufacture is investigated.
A. L. Valko +3 more
doaj
The Potentiostatic Etching of the Metallographic Structure of Stainless Steel
Transactions of the Japan Institute of Metals, 1961 Ito, Naoya, Okamoto, Go
openaire +2 more sources
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
On the potentiostatic Etching of Metallographic Structure of Stainless Steel
Journal of the Japan Institute of Metals, 1960 Naoya Ito, Go Okamoto
openaire +2 more sources
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Cladding is a proven method that boosts the surface qualities of mechanical parts by applying a layer of more durable material over a base substrate. This work responds to the needs of offshore and pressure vessels sectors by focusing on cladding a super austenitic steel onto low‐carbon steel through gas tungsten arc welding.
E. J. da Cruz Junior +6 more
wiley +1 more source
Advanced Materials Technologies, Volume 11, Issue 12, 18 June 2026.This study presents a new biodegradable coating for titanium implants using a natural antimicrobial peptide, caerin 1.9. Applied via solvent casting, the coating offers sustained antibacterial protection and promotes healing. Tested on 3D‐printed porous titanium scaffolds, it effectively prevented infection—including against resistant bacteria—while ...
Hejie Li +7 more
wiley +1 more source