Results 51 to 60 of about 7,952 (183)
Materials and Corrosion, Volume 77, Issue 7, Page 1094-1105, July 2026.The hardness and corrosion resistance of the martensitic stainless steel X30Cr13 depend directly on the applied heat treatment. This article describes and discusses the relationships between alloy composition, thermodynamic phase stabilities, heat treatment parameters, resulting microstructures, and achievable corrosion resistance. To investigate these
Adrian Evia Ocampo +3 more
wiley +1 more source
Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅲ) [PDF]
China Foundry, 2010 Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj
Melt Quality Assessment in Casting of A6082 Alloy [PDF]
Archives of Foundry EngineeringIn this study, it was aimed to examine the metallurgical structures of AA6082 alloys after the casting and homogenization process by means of changing degassing and flux ratios during melt treatment.
B. Tunca +2 more
doaj +1 more source
Natural Sciences, Volume 6, Issue 3, July 2026.A review of advances in chemical analysis brought about by electronic instrumentation. The techniques, and their applications, demonstrate how, collectively, they played a crucial role in transforming the laboratory landscape. If not a relatively recent revolution in one branch of science, it was certainly a transformation.
Anthony S. Travis
wiley +1 more source
Application of metallography in failure investigations: some case studies [PDF]
, 1997 Metallography is a tool to know the internal condition of the material and no investigation can be initiated without this. It can be both nondestruc¬tive i.e., in-situ metallography, as well as destructive i.e..
Sinha, A N
core +1 more source
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 7, Page 2963-2980, July 2026.ABSTRACT This work investigates the performance of the direct current electric potential difference (DCEPD) method for measuring crack extension ( ∆a) during fracture toughness tests of ductile steels exhibiting delaminations perpendicular to the main crack plane, known as splits.
Sergio Luis Gonzalez Assias +2 more
wiley +1 more source
Elementary metallography [PDF]
, 1992 Materials and Processes 1 (MET 141) is offered to freshmen by the Mechanical Engineering Department at Purdue University. The goal of MET 141 is to broaden the technical background of students who have not had any college science courses.
Kazem, Sayyed M.
core
The Role of Molybdenum in the Formation of the Microstructure and Properties of Al-Cu Alloys [PDF]
Archives of Foundry EngineeringThe subject of the presented research is the influence of molybdenum on selected properties of alloys that are based on the Al-Cu system. It could be observed that the introduction of molybdenum to the multi-component alloy at levels of up to 0.5 wt ...
S. Stąpór +4 more
doaj +1 more source
Environmental Barrier Coatings Deposited by Suspension Plasma Spraying
Journal of the American Ceramic Society, Volume 109, Issue 7, July 2026.By taking advantages of high deposition temperature, fully crystalline, crack‐free Yb2Si2O7 EBCs were successfully obtained by suspension plasma spray. However, high amount of Yb2SiO5 phase was found in the as‐sprayed coatings. The formation mechanism of the high amount of Yb2SiO5 phase might be attributed to the high surface ration of the particle for
Dapeng Zhou +4 more
wiley +1 more source
X-ray Metallography, par A. Taylor, 1961
, 1961 Cizeron Georges. X-ray Metallography, par A. Taylor, 1961. In: Bulletin de la Société française de Minéralogie et de Cristallographie, volume 84, 3, 1961. pp.
Cizeron, Georges
core +1 more source