Results 111 to 120 of about 323,922 (291)
Interconnected alternating-current light-emitting diode arrays isolated by laser micromachining [PDF]
, 2011 The fabrication and operation of a monolithic InGaN alternating-current light-emitting diode (LED) based on the bridge rectifier design are demonstrated.
Choi, HW, Lam, EY, Mak, GY
core +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Toward biomaterial-based implantable photonic devices [PDF]
, 2015 Optical technologies are essential for the rapid and efficient delivery of health care to patients. Efforts have begun to implement these technologies in miniature devices that are implantable in patients for continuous or chronic uses.
Cho, Sangyeon +5 more
core +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
IEEE Journal of the Electron Devices Society, 2017 In this paper, we report the design and fabrication of fine-pitch and pixelated-addressed micro-light emitting diode (LED) arrays with emission wavelengths of red (R), green (G), blue (B), and infrared (IR).
Deng Peng, Ke Zhang, Zhaojun Liu
doaj +1 more source
μlED-Based Single-Wavelength Bi-directional POF Link with 10 Gb/s Aggregate Data Rate [PDF]
, 2015 We report record 10 Gb/s bi-directional data transmission over a single 10 m SI-POF, by employing blue micro-light-emitting diodes (μLEDs) at a single wavelength, APD receivers and a PAM-32 modulation scheme.
, +12 more
core +3 more sources
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Digitally Controlled Micro-LED Array for Linear Visible Light Communication Systems
IEEE Photonics Journal, 2015 In a visible light communications (VLC) system, the frequency response of the light-emitting diode (LED) limits the signal bandwidth and, thus, becomes the bottleneck of the transmission data rate.
H. Qian, S. Zhao, S. Z. Cai, T. Zhou
doaj +1 more source