Results 71 to 80 of about 18,614 (250)

Low Cost Micro Milling Machine for Prototyping Plastic Microfluidic Devices

Proceedings, 2018
Micro-milling is one of the commonly used methods of fabrication of microfluidic devices necessary for cell biological research and application. Commercial micro-milling machines are expensive, and researchers in developing countries can’t afford them ...
Md Mubarak Hossain, Tanzilur Rahman
doaj   +1 more source

Experimental Investigation of Cutting Vibration during Micro-End-Milling of the Straight Groove

Micromachines, 2020
Micro-end-milling is a cutting technology that removes redundant material from machined workpieces by small-diameter end mills, and is widely used to manufacture miniature complex parts. During micro-end-milling, the cutting vibration caused by weak tool
Lijie Ma, Ian Howard, Minghua Pang, Zhankui Wang, Jianxiu Su   +4 more
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions

Advanced Functional Materials, EarlyView.
DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng, Qian Yao, Yanan Sun, Hongyu Lv, Zhongchao Bai, Guoliang Zhang, Nana Wang, Jian Yang   +7 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Cyclic Olefin Copolymers as Versatile Materials for Advanced Engineering Applications

Advanced Functional Materials, EarlyView.
Cyclic olefin copolymers (COCs) are presented as highly versatile materials combining tunable synthesis, excellent optical properties, and mechanical robustness. Their potential spans microfluidics, bioengineering, and advanced electronics, while emerging self‐healing and sustainable solutions highlight future opportunities.
Giulia Fredi, Norma Mallegni, Andrea Dorigato, Mario Milazzo   +3 more
wiley   +1 more source

Texoskeletons: Developing the Fundamental Technologies for Creating Intelligent Soft Robotic Clothing With Integrated 1D Sensors and Actuators

Advanced Functional Materials, EarlyView.
ABSTRACT Traditional wearable exoskeletons rely on rigid structures, which limit comfort, flexibility, and everyday usability. This work introduces the fundamental technologies to create the first soft, lightweight, intelligent textile‐based exoskeletons (Texoskeletons) built using 1D sensors and actuators.
Amy Lukomiak, Rameesh Bulathsinghala, Jack Varga, Shuxin Meng, Kalana Marasinghe, Imaad Refai, Biyon Fernando, Amitkumar Patel, Chamika M. Halloluwa‐Arachchige, Carlos Oliveira, Arash M. Shahidi, Zahra Rahemtulla, Alexander Turner, Ziyun Ding, Bernard X. W. Liew, Andy Kerr, Ezio Preatoni, Theo Hughes‐Riley, Ishara Dharmasena, Pasindu Lugoda   +19 more
wiley   +1 more source

Research on Classification and Recognition of Micro Milling Tool Wear Based on Improved DenseNet

IEEE Access
Due to the small size of micro milling tools and wear sizes even in the micrometer range, monitoring tool wear is extremely challenging. The wear state of cutting tools directly affects machining quality and productivity, becoming a key factor ...
Lei Feng, Shuai Zhang, Zhaoxiang Li, Xin Feng   +3 more
doaj   +1 more source

3D Printing Innovations in Polymeric Porous and Patterned Architecture

Advanced Functional Materials, EarlyView.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil, Sri Vaishnavi Thummalapalli, Clarissa Westover, Arunachalam Ramanathan, M. Taylor Sobzcak, Roumika Patil, Qixuan Xiang, Tiantian Li, Sui Yang, Timothy E. Long, Hongyue Sun, Xianqiao Wang, Yang Liu, Kenan Song   +13 more
wiley   +1 more source

Investigation of micro milling processes

, 2010
Micro mechanical machining is conceived by many as the most versatile method of fabricating miniaturized components in complex three-dimensional shapes from a variety of engineering materials. Although this method has several advantages, such as simplicity and flexibility, compared to photolithographic based methods of micro fabrications, it still ...
openaire   +2 more sources