Investigation on the Tool Wear Suppression Mechanism in Non-Resonant Vibration-Assisted Micro Milling [PDF]
Micromachines, 2020 Excessive tool wear during hard and brittle material processing severely influences cutting performance. As one of the advanced machining technologies, vibration-assisted micro milling adds high-frequency small amplitude vibration on a micro milling tool
Lu Zheng, Wanqun Chen, Dehong Huo
doaj +2 more sources
Theoretical and Experimental Investigation of Surface Textures in Vibration-Assisted Micro Milling [PDF]
MicromachinesVibration-assisted micro milling is a promising technique for fabricating engineered mi-cro-scaled surface textures. This paper presents a novel approach for theoretical modeling of three-dimensional (3D) surface textures produced by vibration-assisted ...
Bowen Song +5 more
doaj +2 more sources
Analytical Investigation of the Micro Groove Surface Topography by Micro-Milling. [PDF]
Micromachines (Basel), 2019 Micro-milling is an emerging processing technology for machining micro- and high-precision three dimensional parts that require the use of various materials (with sizes ranging from tens of micrometers to a few millimeters) in the field of advanced manufacturing. Therefore, it can be applied to manufacture the micro parts, but new challenges are raised
Zhang J, Feng C, Wang H, Gong Y.
europepmc +5 more sources
Tool wear propagation in Ti6Al4V laser assisted micro milling using micro ball end mill [PDF]
Jurnal Tribologi, 2018 This paper presents an experimental study of laser assisted micro milling of Ti6Al4V using micro ball end mill. Tool wear propagation was observed and compared between conventional and laser assisted micro milling to evaluate the effectiveness of laser ...
Zazuli Mohid, E. A. Rahim
doaj +2 more sources
Effect of Machining Parameters and Tool Wear on Surface Uniformity in Micro-Milling [PDF]
Micromachines, 2018 In micro-milling, the periodically varying chip thickness, which varies with tool rotation, leads to varying degrees of minimum chip thickness effect and ploughing effect during surface generation.
Zhanwen Sun, Suet To
doaj +2 more sources
Tool Run-Out Measurement in Micro Milling. [PDF]
Micromachines (Basel), 2017 The interest in micro manufacturing processes is increasing because of the need for components characterized by small dimensions and micro features. As a result, researchers are studying the limitations and advantages of these processes. This paper deals with tool run-out measurement in micro milling. Among the effects of the scale reduction from macro
Attanasio A.
europepmc +5 more sources
Analysis on Machining Performance of Nickel-Base Superalloy by Electrochemical Micro-milling with High-Speed Spiral Electrode [PDF]
Micromachines, 2019 As one of the most promising micro-machining methods, electrochemical micro-machining is widely used in the field of metal micro-structures. The electrochemical micro-milling on Nickel-base superalloy by using high-speed spiral electrode was studied in ...
Yong Liu +3 more
doaj +2 more sources
Prediction of Burr Formation in End Micro Milling Poly methyl Methacrylate (PMMA) and Polycarbonate (PC) Substrates Using Convolutional Neural Network (CNN) [PDF]
ITM Web of Conferences, 2023 Polymer microfluidic device is growing in the fields of disease detection, drug synthesis, and environmental monitoring because of the benefits of the miniaturized platforms that provides rapid high-throughput analysis at small sample volumes.
Reddy B Sainatha, Kaur Navneet
doaj +1 more source
Development of Tool Wear Standards and Wear Mechanism for Micro Milling Ti-6Al-4V Alloy
Metals, 2022 With the rapid development of high-precision-device technology, new demands are put forward for micro milling. The size effect and low cutting energy of micro milling make the process expensive and difficult, especially for Ti-6Al-4V alloys.
Tao Zheng +3 more
doaj +1 more source
Comparison of Micro-Milling and Micro-EDM Operations [PDF]
Proceedings of the 8th International Conference on Multi-Material Micro Manufacture, 2011 The production of micro-parts often involves micro-milling and micro-EDM operations. Although both processes are competitive for certain geometries, each of both processes has its specific advantages. Driven by the current trend of hybridization of machining processes it is important to know which process or which combination of processes to use in ...
Vanderauwera, Wouter +4 more
openaire +1 more source