Results 91 to 100 of about 1,212,134 (224)
steel research international, EarlyView.The experiments and simulations demonstrate that, in general, alternative carbon sources can decrease fossil CO2 without adversely impacting EAF process and product. High plastics and tires ratios cause unsafe conditions and poor slag foaming. Hydrogen in EAF burners decreases CO2 but increases water vapor, which can raise the hydrogen content in ...
Ismael Matino +7 more
wiley +1 more source
Quasi in-situ analysis of geometrically necessary dislocation density in α-fibre and γ-fibre during static recrystallization in cold-rolled low-carbon Ti-V bearing microalloyed steel [PDF]
, 2018 In the present study, cold-rolled low-carbon steel is annealed at three different conditions: 700 oC for 0 s, 800 oC for 0 s and 800 oC for 2 min at the heating rate of ~10 oC/s.
Janik, Vit +4 more
core +2 more sources
Influence of Oxygen Contamination on the Genesis of Nonmetallic Inclusions in a Microalloyed Steel
steel research international, EarlyView.Oxygen contamination during melting of steels strongly affects the evolution of nonmetallic inclusions. Controlled remelting experiments, combined with SEM/EDS analysis and thermodynamic simulations, reveal how reoxidation promotes the transformation of alumina‐based inclusions into complex FeO–MnO oxides and other interactions.
Leandro Pianca Prandi +2 more
wiley +1 more source
Development of Microalloyed Intragranular Ferrite Steel With High Strength and Toughness
Teshugang, 2005 The general chemical compositions of microalloyed intragranular ferrite steels are 0.2~0.4C,0.2～0.8Si, 1.0~1.7Mn,0.05～0. 15V. It is a main measure to increase the strength and toughness of ferite-pearlite microalloyed steel using recrystallized forging ...
陈思联, 林军, 戴观文
doaj
A comparison between single sided and double sided friction stir welded 8mm thick DH36 steel plate [PDF]
, 2012 As part of an ongoing process to fully evaluate the potential for friction stir welding (FSW) to be used in the shipbuilding industry, a comparison has been made between two variants of the process.
Cater, Stephen R. +3 more
core
, 2020 Corrosion and stress corrosion cracking (SCC) behavior of some low-alloy high-strength steels microalloyed with Nb and Sb were in detail studied in a simulated polluted marine atmosphere.
Wei Wu +5 more
semanticscholar +1 more source
Materials Characterization, 2020 Aim of the current study is to analyze the fracture toughness values along with other mechanical properties and correlating the microstructures of ultrafine grained (UFG) microalloyed and interstitial free (IF) steels produced through advanced 3-steps ...
Sumit Ghosh, Suhrit Mula
semanticscholar +1 more source
steel research international, EarlyView.This review explains how impurities from recycled scrap affect steel production and performance. Even small amounts (far below 1%) of these impurities can change how steel behaves during fabrication but also affect the properties of the end product. With better understanding and targeted countermeasures, these challenges can be managed, enabling wider ...
Oleksandr Glushko, Ronald Schnitzer
wiley +1 more source
Journal of Materials Research and TechnologyThis study analyzed the deformation behavior of Nb–Ti microalloyed high strength steel at strain rates of 0.001–0.1 s−1 and deformation temperatures of 1050–1150 °C using hot compression tests.
Feng Zhou +6 more
doaj +1 more source
steel research international, EarlyView.High Nb (2.4 wt.%) addition to Maraging 300 steel drives lattice distortion and nanoscale Nb–Mo‐rich precipitation, confirmed by energy‐dispersive X‐ray spectroscopy mapping (Mo ~5.4 wt.%, Nb ~2.5 wt.%). Nanoindentation reveals strong matrix hardening (H >4.8 GPa) at 480°C aging, while 560°C induces ~1.92 vol.% reverted austenite, enabling tunable ...
Laylla Sharon B. Peixoto +9 more
wiley +1 more source