Results 11 to 20 of about 67,929 (267)
Milling Characteristics of Milled Rice According to Milling Ratio of Friction and Abrasive Milling [PDF]
Journal of Biosystems Engineering, 2009 This study was performed to investigate the optimum abrasive and friction milling ratio. This was accomplished by determining changes in the quality, such as whiteness, moisture content, broken kernel, unstripped embryo rate, and surface characteristics or milling difference, during an abrasive and friction based milling process. When only abrasive was
Hoon Kim +3 more
openaire +1 more source
Machines, 2023 A series of experiments were performed aiming at controlling milling force-induced surface errors in the robot-assisted milling process, for the sub-area of the multi-stiffener reinforced inner wall of complex cylindrical thin-walled casting parts, to ...
Yongqiao Jin +3 more
doaj +1 more source
Drought-Tolerance QTLs Associated with Grain Yield and Related Traits in Spring Bread Wheat
Plants, 2022 The present research aims to identify the efficient combination of drought-tolerance selection criteria and associated quantitative trait loci. A panel of 197 bread wheat genotypes was evaluated for yield- and drought-tolerance-related traits in two ...
Sahar Bennani +6 more
doaj +1 more source
Study on jet flushing method for improving debris exclusion in wire EDM
Nihon Kikai Gakkai ronbunshu, 2019 In wire electrical discharge machining (wire EDM), debris tends to stagnate around the wire electrode, since the machined kerf is very narrow. Then, secondary discharges often occur and discharges easily concentrate on the same location, which leads to ...
Tomonori EBISU +2 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2020 In recent years, the surface quality requirement in die and mold has become severer. In addition, die and mold with surface structure are increasing and it makes polishing process difficult.
Yuta SHOWA +2 more
doaj +1 more source
Evaluation of Synchronous Motion in Five-axis Machining Centers With a Tilting Rotary Table
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2007 This paper proposes a new method for evaluating the synchronous inaccuracy of a translational axis and a rotational axis in five-axis controlled machining centers with a tilting rotary table.
Masaomi TSUTSUMI +3 more
doaj +1 more source
A critical review of ionic liquids for the pretreatment of lignocellulosic biomass
South African Journal of Science, 2015 Ionic liquids have been the subject of active research over the course of the last decade and have in the past been touted as one of the most promising technologies for revolutionising the chemical and petro-chemical industries.
Prashant Reddy
doaj +1 more source
Effect of High Speed Milling Process Parameters on the Milling Force and Surface Topography of AM50A Magnesium Alloy [PDF]
Xibei Gongye Daxue Xuebao, 2018 Within the scope of high speed milling process parameters, analyzed and discussed the effects of spindle speed, feed rate, milling depth and milling width on milling forces in the process of high speed milling of AM50A magnesium alloy.
doaj +1 more source
Production of Nanoemulsions from Palm-Based Tocotrienol Rich Fraction by Microfluidization
Molecules, 2015 In the present study, tocotrienol rich fraction (TRF) nanoemulsions were produced as an alternative approach to improve solubility and absorption of tocotrienols.
Pik Seah Goh +4 more
doaj +1 more source
Journal of Advanced Mechanical Design, Systems, and ManufacturingBehind production scheduling lies a trade-off between the comprehensive modeling of production system constraints and quick schedule provision. To realize mass customization, this trade-off must be addressed, requiring a model comprehensive enough for ...
Shinichi INOUE +4 more
doaj +1 more source