Results 61 to 70 of about 207,013 (295)
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Intelligent adaptive control of forces in milling processes [PDF]
, 2007 Intelligent schedules has gained attention in manufacture environments due to increase competence. In this paper an intelligent adaptive discrete control is applied to a practical milling system in order to minimize process malfunctions. Two hierarchical
De la Sen Parte, Manuel +1 more
core +2 more sources
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Experimental Analysis and Geometrical Modeling of Cutting Conditions Effect in 5 Axis Milling with Ti6Al4V Alloy [PDF]
, 2012 The 5 axis continuous milling is an advanced technique for free-form surfaces manufacturing. In finishing, this technique uses ball-end or hemispherical milling cutter.
PRAT, David +3 more
core
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
Advanced Engineering Materials, EarlyView.A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
Effects of Milling Duration on the Thermoelectric Properties of n-Type BI2TE2.7SE0.3 [PDF]
Archives of Metallurgy and Materials, 2019 In this study, an oxide reduction process and a reduction-sintering process were employed to synthesize a thermoelectric alloy from three thermoelectric composite oxide powders, and the thermoelectric properties were investigated as a function of the ...
Min-Soo Park +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour +5 more
wiley +1 more source
Jin'gangshi yu moliao moju gongchengObjectivesHigh-entropy alloys (HEA) with multi-principal elements have many excellent characteristics such as high strength, high hardness and high wear resistance, which have attracted widespread attention from scholars.
Yanwei WU +5 more
doaj +3 more sources