Results 81 to 90 of about 148,150 (316)

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Some aspects about milling : expert system for cutting parameters selection and control designs

, 2006
Milling is a mechanical process which consist of the relative movement between feeding the work-piece and rotating the multitooth cutter, to remove material from the work-piece.
De la Sen, Manuel, Ibeas, Asier, Rubio, Luis   +2 more
core   +1 more source

Numerical simulation of multi-principal elements high-entropy alloy milling based on minimal quantity lubrication

Jin'gangshi yu moliao moju gongcheng
ObjectivesHigh-entropy alloys (HEA) with multi-principal elements have many excellent characteristics such as high strength, high hardness and high wear resistance, which have attracted widespread attention from scholars.
Yanwei WU, Yin LIU, Xingwei SUN, Heran YANG, Zhixu DONG, Weifeng ZHANG   +5 more
doaj   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Simulation of a finishing operation : milling of a turbine blade and influence of damping [PDF]

, 2012
Milling is used to create very complex geometries and thin parts, such as turbine blades. Irreversible geometric defects may appear during finishing operations when a high surface quality is expected.
BALMES, Etienne, GUSKOV, Mikhail, Mikhail Guskov, Gerard Coffignal, Philippe Lorong, COFFIGNAL, Gérard, LORONG, Philippe, Anthony Texier, TEXIER, Anthony, Etienne Balmes   +9 more
core   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Study on Improvement of Machining Accuracy in Machining with CNC Lathe Having a Milling Spindle : Analysis of Workpiece Behavior in Milling and Avoidance of the Resonance [PDF]

, 2012
This study deals with an analysis of workpiece behavior and optimization of machining conditions with regards to milling of a shaft having a small flexural rigidity using ball end mills.
YOSHIDA, Ryoji, KASAHARA, Kazuo, 大久保, 雅文, 吉田, 亮二, OHKUBO, Masafumi, 笠原, 和夫   +5 more
core   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Analytical and experimental study of feed rate in high-speed milling [PDF]

, 2013
In the context of high-speed milling (HSM), during the machining process dynamic machine response has to be identified. To achieve this, we have to calculate the feed rate evolution in linear and circular interpolation according to dynamic performance of
Baili, Maher, Hbaieb, Moncef, Dessein, Gilles, Saï, Wassila Bouzid, Gassara, Bassem   +4 more
core   +1 more source