Results 71 to 80 of about 25,887 (308)

Identification and analysis of cutting force coefficients in the helical milling process

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2020
Cutting forces are often used to optimize cutting parameters and analyze cutting characteristics of the tool. Accurate prediction of cutting forces is critical to understand deeply of the cutting process, especially for helical milling of the difficult ...
Haiyan WANG, Jianyu WANG, Jinming ZHANG, Kexin TAO, Dongxu WU   +4 more
doaj   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

3D FEM Simulation and Experiment Research for Milling Process of Hardened Curved Mold

Journal of Harbin University of Science and Technology, 2018
School of Mechanical and Power Engineering，Harbin University of Science and Technology，Harbin 150080，China) Abstract: In milling process of high hardness curved mold，the change of contact characteristics between cutting tool and workpiece will cause ...
YUE Cai-xu, HAO Sheng-yu, HUANG Cui, WANG Yan-wu   +3 more
doaj   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

A Model for Predicting Dynamic Cutting Forces in Sand Mould Milling with Orthogonal Cutting

Chinese Journal of Mechanical Engineering, 2018
Cutting force is one of the research hotspots in direct sand mould milling because the cutting force directly affects the machining quality and tool wear. Unlike metals, sand mould is a heterogeneous discrete deposition material. There is still a lack of
Zhong-De Shan, Fu-Xian Zhu
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Optimisation of variable helix end milling tools [PDF]

, 2010
High productivity, low cost and high profits are important issues in aerospace, automotive and tool/die metal manufacturing industries. Machining processes are widely used in manufacturing operations for metal manufacturing rather than casting and ...
Yusoff, Ahmad
core  

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Some aspects about milling : expert system for cutting parameters selection and control designs

, 2006
Milling is a mechanical process which consist of the relative movement between feeding the work-piece and rotating the multitooth cutter, to remove material from the work-piece.
De la Sen, Manuel, Ibeas, Asier, Rubio, Luis   +2 more
core   +1 more source