Results 91 to 100 of about 256,076 (285)
Advanced Functional Materials, EarlyView.This study introduces a novel multi‐scale scaffold design using L‐fractals arranged in Archimedean tessellations for tissue regeneration. Despite similar porosity, tiles display vastly different tensile responses (1–100 MPa) and deformation modes. In vitro experiments with hMSCs show geometry‐dependent growth and activity. Over 55 000 tile combinations
Maria Kalogeropoulou +4 more
wiley +1 more source
Focused ion beam milling of brass for microinjection mould fabrication [PDF]
, 2011 In this paper focused ion beam (FIB) milling (sputtering) is demonstrated for the fabrication of brass microinjection moulding inserts which have been previously conventionally milled.
Ratchev, Svetan +2 more
core
Defect Analysis of the β– to γ–Ga2O3 Phase Transition
Advanced Functional Materials, EarlyView.The role of defects at all the relevant stages of the β$\beta$‐ to γ$\gamma$‐Ga2O3 polymorph transition is investigated using a multi method approach. The positron annihilation spectroscopy based results show that the defect density decreases after the transition, and that changes in defect configuration within the γ phase occur with increasing ...
Umutcan Bektas +9 more
wiley +1 more source
Dry milling of magnesium based hybrid materials
Periodica Polytechnica Transportation Engineering, 2008 In the transportation industry, a general desire is to reduce the energy consumption. One way to achieve this is the use of light weight metals like magnesium and its´ alloys. An alternative solution is the use of magnesium based hybrid structures which are combinations of magnesium and another material like aluminium or steel in one machine part ...
Péter Ozsváth +2 more
openaire +2 more sources
Advanced Functional Materials, EarlyView.A solvent‐free mechanochemistry‐enabled supramolecular engineering strategy is developed to directly synthesize covalent‐interconnected two‐dimensional atomic‐layered carbon nitride nanosheets photocatalyst, bypassing conventional top‐down exfoliation requirements.
Fanglei Yao +7 more
wiley +1 more source
Investigation of experimental study of end milling of CFRP composite
Science and Engineering of Composite Materials, 2015 Carbon fiber-reinforced plastic (CFRP) composites are materials that are difficult to machine due to the anisotropic and heterogeneous properties of the material and poor surface quality, which can be seen during the machining process.
Kiliçkap Erol +2 more
doaj +1 more source
Advanced Functional Materials, EarlyView.Free‐standing plasmonic gold‐based fractal antennas are fabricated by 3D nanoprinting, employing focused electron beam induced deposition and an optimized purification method to remove carbon while conserving structural fidelity. Simulation and experiment show broadband plasmonic activity, including customizable polarizability, thereby paving the way ...
Verena Reisecker +6 more
wiley +1 more source
Jin'gangshi yu moliao moju gongchengObjectivesHigh-entropy alloys (HEA) with multi-principal elements have many excellent characteristics such as high strength, high hardness and high wear resistance, which have attracted widespread attention from scholars.
Yanwei WU +5 more
doaj +1 more source
A New Method to Recycle Stainless–Steel Duplex UNS S31803 Chips
Metals, 2018 Due to the increased consumption of raw materials, energy, and the waste it generates, recycling has become very important and fundamental for the environment and the industrial sector.
Mendonça Claudney +7 more
doaj +1 more source
EFFECT OF HARD RED SPRING WHEAT CONSISTENCY ON MILLING VALUE [PDF]
Increased concerns over the quality of wheat in domestic and export markets has focused attention on the consistency of wheat quality. This study utilized three measures to examine the effect of variability in characteristics on the milling value of ...
Dahl, Bruce L., Wilson, William W.
core +1 more source