Results 31 to 40 of about 256,076 (285)
Impact of ball milling on maize (Zea mays L.) stem structural components and on enzymatic hydrolysis of carbohydrates [PDF]
, 2014 The impact of ball milling on structural components of maize (Zea mays L.) stem was investigated in relation to enzymatic hydrolysis of carbohydrates. Ball milling of extractive-free maize stem material was carried out with different milling times up to ...
Baumberger, Stéphanie +2 more
core +3 more sources
Analysis of the Machining Process of Titanium Ti6Al-4V Parts Manufactured by Wire Arc Additive Manufacturing (WAAM) [PDF]
, 2020 In the current days, the new range of machine tools allows the production of titanium alloy parts for the aeronautical sector through additive technologies.
Alonso, Unai +3 more
core +2 more sources
Parameter Optimization of Milling Process for Surface Roughness Constraints
Journal of Harbin University of Science and Technology, 2023 In the milling process of 6061 aluminum considering the requirement of controlling the surface roughness of workpiece, artificially selected milling parameters may be conservative, resulting in low material removal rate and high manufacturing cost ...
GUO Bin +5 more
doaj +1 more source
Carbon fibre recycling from milling dust for the application in short fibre reinforced thermoplastics [PDF]
, 2017 A new approach to reuse accruing chips and dust from milling operations of carbon reinforced plastics (CFRP) is studied, show-ing how CFRP milling dust, in comparison to primary and pyrolysed fibres, can find application as a filler material in thermo ...
Meier, Paul, Uhlmann, Eckart
core +1 more source
Laser-assisted Milling of Advanced Materials
Physics Procedia, 2011 AbstractAdvanced high-strength materials offer a huge application potential within highly stressed components in various industrial areas. But their machinability is still limited when applying established and conventionally available technologies. Aiming at the reduction of process forces, increased material removal rates and longer tool service life ...
Brecher, Christian +3 more
openaire +1 more source
Synthesis of SnSb2Te4 Microplatelets by High-energy Ball Milling [PDF]
Materials Research, 2015 In this work we demonstrate that high-energy ball milling process can be used to synthesize SnSb2Te4 without surfactant and further annealing. Milling parameters such as ball to raw material ratio (5:1) and milling time (2h) were determined to be ...
Mário Sérgio da Luz +5 more
doaj +2 more sources
Investigation of CNC Milling Machining Parameters on Surface Roughness
Al-Khawarizmi Engineering Journal, 2018 Milling Machining is a widely accepted nontraditional machining technique used to produce parts with complex shapes and configurations. The material is removed in two stages roughing and finishing, the flat end cutter removed the unwanted part of ...
Rasha Ramiz Alyas
doaj +1 more source
Defects induced ferromagnetism in Mn doped ZnO
, 2010 Single phase Mn doped (2 at %) ZnO samples have been synthesized by solid-state reaction technique. Before the final sintering at 500 C, the mixed powders have been milled for different milling periods (6, 24, 48 and 96 hours).
A. Banerjee +45 more
core +1 more source
Modeling dynamics of parallel milling processes in time-domain [PDF]
, 2010 The use of parallel milling processes is increasing in various industries due to several advantages of these machine tools. Parallel milling processes are the processes where more than one milling tool simultaneously cut a workpiece.
Budak, Erhan +2 more
core
Laser Milling of the Intractable Materials
Procedia CIRP, 2013 AbstractIn comparison with high-speed cutting and electrical discharge machining, laser milling is the most universal method for shaping of any type of materials (including natural and artificial diamonds, alloys etc.).The investigation of laser milling was done using Q-switched YAG laser.
Kovalenko, V. +7 more
openaire +1 more source