Results 31 to 40 of about 37,685 (267)

Study of milling process basics for the biocompatible PEEK material

Materials Research Express, 2020
Polyetheretherketone (PEEK) material has attracted attentions and studies in the medical field due to its excellent properties suitable for orthopedic, dental, and implant applications.
Yang Li, Xiang Cheng, Siying Ling, Guangming Zheng, Huanbao Liu, Lei He   +5 more
doaj   +1 more source

MILLING PROCESS PARAMETERS AND TAGUCHI METHOD

, 2022
To safeguard the quality of the products machined at the least costs along with the greatest amount of efficiency during machining, the selection of the ideal parameters is very necessary. Usually the working of an experienced operator is very necessary for the selection of an ideal cutting condition for the metal.
Mohit Balkrishna Diwan, Sonal Chandubhai Yogi   +1 more
openaire   +1 more source

The Influence of Milling Parameters on Surface Properties in Milled AZ91C Magnesium Alloy

Iranian Journal of Materials Science and Engineering, 2021
A full factorial design of experiment was applied running 36 experiments to investigate the effects of milling parameters including cutting speed with three levels of 62.83, 94.24 and 125.66 m/min, feed rate with three levels of 0.1, 0.2 and 0.3 mm/tooth, cutting depth with two levels of 0.5 and 1 mm and machining media with two levels, on surface ...
Mostafapour, Amir, Mohammadi, Milad, Ebrahimpour, Ali   +2 more
openaire   +2 more sources

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Effect of Tooth Wear on the Technological Parameters of the Milling Process of Asphalt Concrete Layers

Lubricants
This article discusses the findings of an experimental study designed to investigate the cutting forces encountered during the milling of asphalt pavement, considering the influence of cutter teeth wear.
Marius Gabriel Petrescu, Teodor Dumitru, Eugen Laudacescu, Maria Tănase   +3 more
doaj   +1 more source

Optimization of Drying Kinetics and Stone Milling of Chickpea (Cicer arietinum): An Investigation of Moisture Content and Milling Speed Effects on Mill Operative Parameters, Particle Size Distribution, and Flour Composition

Applied Sciences, 2023
Chickpeas are one of the most widely consumed legumes in the world. Nevertheless, the literature is lacking studies on the effect of drying and milling processes on chickpea flour characteristics, thus motivating this work.
Alessio Cappelli, Mauro Zaninelli, Sirio Cividino, Mattia Fiscella, Enrico Cini, Alessandro Parenti, Piernicola Masella   +6 more
doaj   +1 more source

Milling stability for slowly varying parameters

Procedia CIRP, 2018
Abstract In order to predict the quality and the stability properties of milling processes, the relevant dynamics reduced to the cutting edges needs to be known. However, the dynamics varies through the workspace along the tool path during a given machining operation.
Dombovari, Zoltan, Munoa, Jokin, Kuske, Rachel, Stepan, Gabor   +3 more
openaire   +2 more sources

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source