Results 181 to 190 of about 47,989 (262)

A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials

Advanced Engineering Materials, EarlyView.
This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline, Matthew Santer, Robert Hewson   +2 more
wiley   +1 more source

Mechanistic insights into facet-dependent CO adsorption and vibrational responses on anatase TiO₂: periodic quantum-mechanical calculations. [PDF]

J Mol Model
Vacek J, Hobza P, Nachtigallová D.
europepmc   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Advanced Materials and Processing Technologies. [PDF]

Materials (Basel)
Ćurković L, Jozić S, Žmak I.
europepmc   +1 more source

Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release

Advanced Engineering Materials, EarlyView.
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro, Manuel J. Carvajal Loaiza, Rahaf Homssi, Vanessa Restrepo   +3 more
wiley   +1 more source

Rapid Design and Fabrication of Body Conformable Surfaces with Kirigami Cutting and Machine Learning. [PDF]

Adv Sci (Weinh)
Bali J, Li J, Chen J, Li S.
europepmc   +1 more source

Copper Nanocrystallization in Anodic Oxide Films of Ti–Cu‐Based Bulk Metallic Glass and Its Effect on the Corrosion Resistance and Cytocompatibility

Advanced Engineering Materials, EarlyView.
Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan, Nora Fernández Navas, Thorgund Nemec, Ivan Kaban, Ute Hempel, Andrea Voss, Volker Hoffmann, Darius Pohl, Annett Gebert   +8 more
wiley   +1 more source

Parameterized shape optimization of a bi-leaflet heart valved conduit for pediatric applications. [PDF]

Eng Comput
Luo C, Li K, Herschman AR, Sun M, Waisman H, Vedula V, Kysar JW, Kalfa D.   +7 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

A Machine Learning Interatomic Potential Data Set and Model for Catalysis with Local Fine-Tuning to Chemical Accuracy. [PDF]

JACS Au
Wu Z, Zhou L, Hou P, Liu Y, Wang R, Guo T, Liu JC.   +6 more
europepmc   +1 more source