Results 61 to 70 of about 26,093 (264)

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Mixed Mode I-II Fracture Path and Initiation Angle of Concrete at Mesoscale Level

Advances in Materials Science and Engineering, 2019
This paper presents the mesolevel numerical simulation and experimental verification of mixed mode I-II fracture for the four-point shearing beam with a single-side notch based on the concrete damaged plasticity (CDP) method and the Monte Carlo ...
Guodong Li, Zhengyi Ren, Zhiyuan Wang, Jiangjiang Yu, Zhimeng Zhao   +4 more
doaj   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

On fracture criteria in phase field model for fracture in asphalt concrete

Case Studies in Construction Materials
Extensive research has explored cracking in asphalt mixtures under pure mode-I conditions; however, heavy traffic loads often lead to crack formation under mixed-mode fracture conditions in asphalt pavements.
Ghufranullah khan, Awais Ahmed, Hassan Amjad, Aizaz Ahmad, R. Nawaz, Mudassir Iqbal   +5 more
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

In-plane mixed-mode brittle fracture assessment of Harsin marble using HCSP specimen

Fracture and Structural Integrity
The primary objective of this manuscript is studying the effect of T-stress term (T) on the crack propagation angle (CPA) and fracture toughness of in-plane mixed mode loading by utilizing a generalized form of minimum strain energy density (SED ...
Z. Moqadaszadeh, H. Salavati, M. Rashidi Moghaddam   +2 more
doaj   +1 more source

From High Strain Rates to Elevated Temperatures: Investigating Mixed-Mode Fracture Behaviour in a Polyurethane Adhesive. [PDF]

Polymers (Basel), 2023
Ribas MJP, Akhavan-Safar A, Pigray N, Carbas RJC, Marques EAS, Borges CSP, Wenig S, da Silva LFM.   +7 more
europepmc   +1 more source

Semantic Modeling in Materials Science and Engineering With Platform MaterialDigital Core Ontology 3.0

Advanced Engineering Materials, EarlyView.
The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling, Philipp von Hartrott, Jörg Waitelonis, Thomas Hanke, Henk Birkholz, Hossein Beygi Nasrabadi, Khashayar Razghandi, Kamilla Zaripova, Felix Thonagel, Fabian Neuhaus, Martin Glauer, Lars Vogt, Harald Sack, Lutz Mädler, Bernd Bayerlein, Chris Eberl   +15 more
wiley   +1 more source